Jenn-Air JUIFX15HX Installation Manual Download Page 38

Page: 38 / 40

INSTALLATION

38 | INSTALLATION

INSTALLING AUXILIARY GRILL

The auxiliary grill is an optional accessory. It can

be used to align the toe grill with the rest of the

cabinets (while not obstructing ventilation of

the ice maker).

NOTE:

Install auxiliary grill only after finishing

the complete ice maker installation.

Remove packaging material and

discard it.

Using power drill and a 1/8" drill bit, drill

holes in cabinet. This is to fit screws of

size #8-18 x 0.750".

Remove the screws that are taped

inside the auxiliary grill.

Place grill onto cabinetry. Align part so

that grating pattern on the auxiliary

grill matches that of the toe grill on the

ice maker.

Center auxiliary grill on cut out for ice

maker. Mark hole locations on each

side of auxiliary grill on cabinet.

Using the TORX T20 screwdriver, screw

auxiliary grill into cabinet.

Summary of Contents for JUIFX15HX









































Search results

Summary of Contents for JUIFX15HX

Reviews:

Related manuals for JUIFX15HX

Brands by name

Popular brands

Jenn-Air JUIFX15HX, Installation Manual

Search results

Summary of Contents for JUIFX15HX

Reviews:

Related manuals for JUIFX15HX

Brands by name

Popular brands