background image

To Disconnect the Water Line:

• Push in white collar (A) and hold.

• Pull the door-side tube from the connector (B).

To Reconnect the Water Line:

• Firmly push tube 

5

8

” into the connector. Use

lines on the tube as a guide for full insertion.

• If tube end is damaged, cut off 

5

8

” before

reconnecting.

• If leaking occurs,

reconnect the line.

3. Close doors.

4. Remove top hinge covers by

removing Phillips screws.

5. Unscrew 

5

16

” hex head screws from

top hinges.

6.

For ice and water dispensing
models only:

Detach main wire

connector harness.

• Do not remove screw

connecting green ground wire.

• To detach main wire harness,

use a flat blade tool or finger-
nail to press junction point
between two connectors to
release.

7. Remove top hinges along with doors.

4

I

NSTALLATION

To avoid severe personal injury or death, observe the
following:

• Disconnect power to refrigerator before removing

doors. Connect power only after replacing doors.

• Green ground wire must be attached to top hinge

while performing door removal and replacement.

• Tape decorative panels (select models) securely

into place before removing door handles.

WARNING

To avoid property damage, observe the following:

• Protect vinyl or other flooring with cardboard,

rugs or other protective material, prior to moving
refrigerator.

Do not

adjust refrigerator to be any shorter than

68

1

2

” tall (minus hinge and cap). Doing so may

damage underside components.

CAUTION

Door and Hinge Removal

Some installations require door removal to get
refrigerator to final location.

1.

Unplug power cord from power source.

2. Remove toe grille and bottom hinge covers (see

page 9).

• Open both doors 180°, or as wide as possible.

For ice and water dispensing models only:

Remove the left side hinge cover by carefully
pulling the water line to pry the cover loose. Then
continue to maintain downward pressure to the
notched side of the cover while swinging it off
(see page 9).

8. Remove bottom hinges with a 

3

8

” hex head driver.

Replacing the Doors

• To replace the doors, follow the steps in 

Door and

Hinge Removal

in reverse order.

IMPORTANT:

If water line tube end is damaged, cut

off 

5

8

” before reconnecting.

Note

• For refrigerators in operation, shut off water before

removing water line from the door.

A

B

Summary of Contents for JCD2295KE








Reviews: