2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Parts supplied
■
Vent grille
■
Grease filter
■
Grill cartridge
■
Grease container(s)
■
Hold-down straps (4)
■
Clamping screws (4)
Parts needed
■
A UL listed or CSA approved strain relief for
⁷⁄₈
" (2.2 cm)
knockout.
■
A UL listed or CSA approved conduit connector for
¹⁄₂
" (1.3 cm) trade-size metal-clad conduit
■
UL listed wire connectors
■
Metal ducting
■
Jenn-Air wall cap
Jenn-Air
®
6" (15.2 cm) Round Surface Wall Cap Damper
Order Part Number A406
Jenn-Air
®
3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper
Order Part Number A403
To order, see the “Assistance or Service” section of the Use
and Care Guide.
■
Vent clamps
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
When installing cooktop, use minimum dimensions given.
■
To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
■
Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
■
If cabinet has drawers, drawers will need to be removed and
drawer fronts installed on front of cabinet.
IMPORTANT: An under-counter built-in oven cannot be installed
under this product.
Product Dimensions
20" (50.8 cm) Single Cartridge Cooktop
*NOTE: Grills installed near a side wall must allow a minimum
clearance of 6" (15.2 cm) between cooktop and sidewall for
maximum performance. Minimum clearance of 1" (2.5 cm) is
required to sidewalls and ¾" (1.9 cm) to rear wall.
*A minimum clearance of
6¹⁄₄
" (15.9 cm) is recommended for
removal of the grease filter(s). Installed dimension for the grease
filter(s) is 5
¹⁄₂
" (14.0 cm).
**A minimum clearance of
2
" (5.1 cm) is required between the
blower motor and cabinet for proper cooling. A clearance of
6" (15.2 cm) is recommended to allow for blower motor service.
■
Tape measure
■
Flat-blade screwdriver
■
Phillips head screwdriver
■
Drill
■
Level
■
6" socket extension
■
Marker or pencil
■
Pliers
■
¼" drill bit
■
Jigsaw
■
Ratchet with
³⁄₈
" socket
A. 19¼" (48.9 cm)
B. 21
¹⁄₈
" (53.6 cm)
C. Grease container
D. Blower
A. Side clearance - See *NOTE.
B. 4¾" (12.0 cm)
C. 6¼" (15.9 cm)
D. Grease container
E. 2" (5.0 cm) min. to cabinet,
6" (15.2 cm) recommended to motor service
F. 12½" (31.8 cm)
G. 17½" (44.5 cm)
A
B
C
D
B
C*
G
A
D
E**
F
