manualshive.com logo in svg

JENCO VisionPlus EC3175, Operation Manual, Page: 11 / 12

Share
Download
JENCO VisionPlus EC3175 Operation Manual Download Page 11

10

SPECIFICATIONS

Display

Range

Resolution

Accuracy

Conductivity/

TDS

K=0.01

0.000 to 1.999 uS/cm /

0.000 to 1.999 mg/L

2.00 to 19.99 uS/cm /

2.00 to 19.99 mg/L

0.001 uS/cm /

0.001 mg/L

0.01 uS/cm /

0.01 mg/L

±0.5% F.S.

Conductivity

TDS

K=0.1

0.00 to 19.99 uS/cm /

0.00 to 19.99 mg/L

2.0 to 199.9 uS/cm /

2.0 to 199.9 mg/L

0.01 uS/cm /

0.01 mg/L

0.1 uS/cm

0.1 mg/L

±0.5% F.S.

Conductivity/

TDS

K=1.0

0.0 to 199.9 uS/cm /

0.0 to 199.9 mg/L

200 to 1999 uS/cm /

200 to 1999 mg/L

2.00 to 19.99 mS/cm /

2.00 to 19.99 g/L

0.1 uS/cm /

0.1 mg/L

1 uS/cm /

1 mg/L

0.01 mS/cm /

0.01 g/L

±0.5% F.S.

Conductivity/

TDS

K=10.0

0 to 1999 uS/cm /

0 to 1999 mg/L

2.00 to 19.99 mS/cm /

2.00 to 19.99 g/L

20.0 to 199.9 mS/cm /

20.0 to 199.9 g/L

1 uS/cm /

1 mg/L

0.01 mS/cm /

0.01 g/L

0.1 mS/cm /

0.1 g/L

±0.5% F.S.

Temperature

0.0 to 100.0 °C

0.1 °C

±0.2 °C

Reference Temperature

15.0 to 25.0 °C

Temperature Coefficient

0.0 to 4.0% default at 1.91%

Cell Constant

0.01; 0.10; 1.00; 10.0

TDS Constant

0.30 to 1.00, default at 0.65

Power

100 ~ 240 VAC adapter

or AAA x 6

Calibration Back-up

EEPROM

Audio Feedback

All Touch Keys

Display

(Conductivity/TDS: Temp)

22 mm : 14.5 mm high LCD

Ambient Temperature Range

0 to 50 °C

Relative Humidity

up to 90%

Case

IP54

Dimensions (W x D x H)

150 x 203 x 72 mm

Weight

504 grams(Batteries included)

Summary of Contents for VisionPlus EC3175













Reviews:

No comments