manualshive.com logo in svg

JENCO VisionPlus EC3175, Operation Manual, Page: 10 / 12

Share
Download
JENCO VisionPlus EC3175 Operation Manual Download Page 10

9

normal. Allow temperature to stabilize before taking

measurements.

ERROR DISPLAYS AND TROUBLESHOOTING

[Note:

If the meter still does not perform normally after the above

measures are taken, call

Jenco

representative.

]

Main

Display

Secondary

Display

Possible cause(s)

Corrective

Action(s)

"over" during

measurements 0.0~100.0

℃

●

Sample

Conductivity

value > 200.0mS;

Sample TDS >

200g/L.

●

Conductivity cell

contaminated or

defective.

●

Incorrect K

constant value

input.

●Sample cannot be

tested

.

●

Decontaminate /

clean cell or

replace cell.

●Input correct K

value.

"over" during

calibration

/

●

Incorrect standard

solution.

●

Conductivity cell

contaminated or

defective.

●

Incorrect K

constant value

input.

●Replace standard

solution.

●Decontaminate /

clean cell or

replace cell.

●Input correct K

value.

"over " during

measurements

over

●

Sample

temperature >100

℃

.

●Reduce sample

temperature.

●

Defective

conductivity cell.

●Replace cell.

undr

●

Sample

temperature

<0.0

℃

●Increase sample

temperature.

●

Defective

conductivity cell.

●Replace cell.

Summary of Contents for VisionPlus EC3175













Reviews:

No comments