Jema Autolifte JA3500T, Original Instruction

Page: 3 / 32

Jema Autolifte – Denmark
- WE ARE HERE TO SURPRISE!
3
1.
Important safety instructions
1.1 Important notices
Jema Autolifte will give the user one-year warranty of quality for the machine. If something wrong with the machine within the
term of service, we will repair or replace the product according to the user’s demand. The manufacturer will not take any
responsibility for improper installation and operation, overload running, wrong concrete ground (that cannot meet the
requirements in the manual), normal mechanical abrasion and insufficient maintenance. The warranty will be carried out on the
basis of the type and serial number of the equipment. Therefore, the users shall provide them to the manufacturer when asking
service.
The 2-post lift is suitable for lifting motor vehicles having maximum weight as described, any other use is to be considered
improper and irrational and thus highly forbidden. The constructor cannot be held responsibilities for any damage or injuries
caused by an improper use or by the non-observance of the following instructions.
Read this guide carefully before using the machine and follow the instructions given by this guide to grant the machine a correct
function, efficiency and a long service life.
1.2 Qualified personnel
1.2.1 The lift may only be used by qualified staff, properly trained for the specific use of the machine.
1.2.2 The wiring must comply with local code and a certified electrician for electrical hook up.
1.2.3 Only authorized personnel are allowed in lifting area.
1.3 Danger notices
1.3.1 Do not install the lift on any asphalt surface
1.3.2 Read and understand all safety warning procedures before operating the lift.
1.3.3 The lift, in its standard version, is not designed for outdoor use.
1.3.4 Keep hands and feet away from any moving parts. Keep feet clear of lift when lowering.
1.3.5 The lift may only be used by qualified staff, properly trained for the specific use of the machine.
1.3.6 Do not wear unfit clothes such as large clothes with flounces, tires, etc, which could get caught by moving parts of the
machine.
1.3.7 The lift surrounding area must be free from people or objects which could be a danger for lifting operations.
1.3.8 The lift is only designed to lift the entire body of vehicle, having maximum weight not more than the lift capacity.
1.3.9 Always insure the safety devices are engaged before any attempt to work on or near vehicle.
1.3.10 The vehicle must be centered and positioned in a stable correct way with respect to the posts and following the
instructions given by manufacturer.
1.3.11 Make sure that the machine and its devices are working correctly, according to the specific instructions for maintenance
1.3.12 Lower the lift to its lowest position when service finishes.
1.3.13
Do not modify the machine without manufacturer’s advice.
1.3.14 If the machine is not to be used any more, owners is suggested to removing the power supply connections, emptying the
oil tank and disposing the liquids by right way.
1.3.15 If the lift is to be left unused for a long period, proceed as follows:
a. Disconnect the energy source
b. Empty the oil tank
c. Grease the moving parts which might be damaged by dust or drying out
1.4 Condition notices
Generally, this machine will be installed on the following conditions:
1.4.1 Supply voltage: 0.9 - 1.1 nominal supply voltage
1.4.2 Source frequency: 0.99 - 1.01 nominal frequency
1.4.3 Ambient temperature: 5
°
C - 40
°
C
1.4.4 Altitude: shall be at altitudes up to 1000m above mean sea level
1.4.5 Relative humidity: not exceed 50% at 40
°
C
1.4.6 Atmosphere: Free from excessive dust, acid fume, corrosive gases and salt.
1.4.7 Avoid exposing to direct sunlight or heat rays which can change the environmental temp.
1.4.8 Avoid exposing to abnormal vibration.
1.4.9 Electrical equipment shall withstand the effects of transportation and storage temperature within a range of -25
°
C to 55
°
C
and for short periods not exceeding 24 hours at up to +70
°
C.