background image

NOTE FROM JEFF ROWLAND DESIGN GROUP

elcome to the Jeff Rowland Design Group “family” and congratulations on your 
purchase of what is unquestionably one of the world’s finest amplifiers. With its 

combination of features such as precision electronic circuitry, exceptional efficiency, and 
accurately machined chassis components throughout, your 

MODEL 625 STEREO AMPLIFIER

 will 

offer you many years of musically satisfying enjoyment.

Please take a few minutes to read the remainder of this Owner’s Manual before proceeding 
with the installation of the amplifier. A thorough understanding of the operational features 
will allow you to gain the maximum performance and ease of use for which this amplifier was 
designed. 

Please note that your 

MODEL 625 STEREO AMPLIFIER

 serial number begins with the letters “SB”. 

Please include this number with any correspondence regarding your 

MODEL 625 STEREO 

AMPLIFIER

. It has been my joy to create an audio component of enduring value that reflects the 

highest ideals of musical and artistic expression. It is my hope that these qualities will enrich 
your experience and pride of ownership.

If you have any additional questions regarding the installation or operation of the 

MODEL 

MODEL 625 STEREO AMPLIFIER

, please contact your authorized Jeff Rowland Design Group dealer 

or check the Jeff Rowland Design Group web site at http://jeffrowland.com.

Enjoy the music!

Jeff Rowland
President, Jeff Rowland Design Group

W

 

PAGE  4

Summary of Contents for 625














Reviews: