background image

P/N 960-100925R_Rev. A {EDP #186705} 

© 2010, Japan CashMachine Co, Limited

2 6

Transaction Based Validator Integration Guide

Blue

Green

(13)

Banknote Length 

Problem

The Line Sensors calculated a Banknote length longer or shorter than the rated 

value.
[Solution] Check that the following parts are properly assembled and/or Harness 

connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Line Sensor.
If the error is not resolved, change the above related part or parts.

Blue

Green

(14)

2-Color Margin 

Problem

The Line Sensors calculated that the 2-Color margin of a Banknote is greater than 

the rated value.
[Solution] Check that the following parts are properly assembled and/or Harness 

connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Line Sensor.
If the error is not resolved, change the above related part or parts.

Blue

Green

(15)

Counterfeiting 

Banknote Action

The Banknote has been validated as a Counterfeiting Banknote.
[Solution] Check that the following parts are properly assembled and/or Harness 

connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Line Sensor.
If the error is not resolved, change the above related part or parts.

Blue

Green

(16)

3-Color 

Comparison 

Problem

The Line Sensors calculated a 3-Color comparison that is greater than the rated 

value.
[Solution] Check that the following parts are properly assembled and/or Harness 

connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Line Sensor.
If the error is not resolved, change the above related part or parts.

Table 22 

LED Flash Reject Error Codes (Continued)

On-line

Off-line

Error

Causes and Solutions

LED Color

(Lit)

LED Color

(Flash

Sequence)

Summary of Contents for TBV Series











































Reviews:

Related manuals for TBV Series