background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0845 6005526

Maintenance

7

Maintenance on the blade is best if conducted at a
specialised Centre that has the most appropriate
tools.
Only blades with the following codes must be used
on this machine:

81004146/0

Blades must always be marked 

. Given the prod-

uct evolution, the above mentioned blade may be
replaced in time by others, with similar interchange-
able and operating safety characteristics. 
Reassemble the blade (2) with the code and mark-
ings facing the ground, following the order indicated
in the illustration.  

Tighten the central screw (1) using a torque wrench
set to 35-40 Nm.

paint may detach over time due to the abrasive
action of cut grass; in this case, promptly touch-up
paint with rust-proof paint to prevent rusting that
could corrode the metal.

4)  Should it be necessary to access the lower part, only

tilt the machine from the side shown in the engine
handbook; following the relative instructions.

5)  Do not drip petrol onto the plastic parts of the motor

or the machine to prevent damaging them and
remove all traces of spilt petrol immediately. The war-
ranty does not cover damage to plastic parts caused
by petrol.

IMPORTANT – Regular, careful maintenance is
essential for keeping the safety level and original
performance of the machine unchanged in time.
Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning,

maintenance or adjustment operation on the machine.

2)  Carefully clean the machines with water after each

cut; remove the grass debris and mud accumulated
inside the chassis to avoid their drying and thus mak-
ing the next start-up difficult.

3)  In models with painted chassis, internal chassis part

2

1

For JCB Mulcher 48 S only:

Remove the guard (1) once or twice a year by
unscrewing the screws (2) and releasing the cou-
plings (3). 

Then clean carefully using a brush or compressed
air, removing the grass and dirt from the area around
the transmission and belt. Always refit the guard (1). 

1

2

3

JCB rsb 48_11-171503976/0:JCB rsb 48_11-171503976/0  7-12-2010  10:26  Pagina 7

Summary of Contents for MULCHER 48









Reviews: