background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092  

other accessory. Pinching or 
snagging causes rapid stalling 
of the rotating accessory which 
in turn causes the uncontrolled 
power tool to be forced in 
the direction opposite of the 
accessory’s rotation at the point 
of the binding.
For example, if an abrasive disc 
is snagged or pinched by the 
workpiece, the edge of the disc 
that is entering into the pinch 
point can dig into the surface of 
the material causing the disc to 
climb out or kick out. The disc 
may either jump toward or away 
from the operator, depending on 
direction of the disc’s movement 
at the point of pinching. Abrasive 
discs may also break under these 
conditions.
Kickback is the result of power 
tool misuse and/or incorrect 
operating procedures or 
conditions and can be avoided 
by taking proper precautions as 
given below.
a)

 Maintain a firm grip on the 

power tool and position your body 
and arm to allow you to resist 
kickback forces. Always use 
auxiliary handle, if provided, for 
maximum control over kickback 
or torque reaction during start-up. 

The operator can control torque 
reactions or kickback forces, if 
proper precautions are taken.
b)

 Never place your hand near 

the rotating accessory. 

Accessory 

may kickback over your hand.

c) Do not position your body in 
the area where power tool will 
move if kickback occurs. 

Kickback 

will propel the tool in direction 
opposite to the disc’s movement 
at the point of snagging.
d)

 Use special care when working 

on corners, sharp edges etc. 
Avoid bouncing and snagging the 
accessory. 

Corners, sharp edges 

or bouncing have a tendency to 
snag the rotating accessory and 
cause loss of control or kickback.
e)

 Do not attach a saw chain 

woodcarving blade or toothed 
saw blade. 

Such blades create 

frequent kickback and loss of 
control.

Additional safety instructions 
for grinding and cutting-off 
operations

Safety Warnings Specific for 
Grinding and Abrasive Cutting-Off 
Operations:

a)

 Use only disc types that are 

recommended for your power tool 
and the specific guard designed 
for the selected disc.

 Discs for 

which the power tool was not 
designed cannot be adequately 
guarded and are unsafe.
b)

 The guard must be securely 

attached to the power tool and 
positioned for maximum safety, 
so the least amount of disc is 

Summary of Contents for JCB-AG2300





























Reviews: