background image

8025 ZTS, 8026 CTS, 8030 ZTS, 8035 ZTS

21

Troubleshooting/FAQs

Issue / FAQ

Resolution/Answer

How do I release pressure from my 
Auxiliary system?

Turn key to position 1, enter immobiliser code (if required). Enable 
Hydraulic controls, press the swing/aux button to select auxiliary, if the 
AUX indicator lamp is lit on the instrument panel is illuminated auxiliary 
has been selected. Make sure this is the case. Then use the swing/aux 
pedal and operate the auxiliary circuit to discharge any stored pressure.

What are the max flow of the 
Auxiliary circuits?

The maximum flow for the hydraulic circuits are as follows:
8025: 190 bar
8026: 190 bar
8030: 190 bar
8035: 206 bar 

Is it possible to turn off the lift 
overload buzzer?

Yes. This can be done using the momentary rocker switch on the right 
hand console when the ignition switch is in the on position.

Can you dig to dozer?

Digging to dozer can not be done while machine dig end is central to 
the dozer. To dig to dozer slew machine over to the side then use the 
boom swing to offset the boom enabling digging up to the dozer. *

* This is known by if the aux lamp on the instrument panel is not on. If it is press the left joystick button in until the lamp is turned off.

Summary of Contents for 8025 ZTS

























Reviews: