background image

 01 - Machine

 03 - Safety

 09 - General Safety

01 - 5

9813/2850-3

01 - 5

09 - General Safety
Introduction

Training

To operate the machine safely you must know the

machine and have the skill to use it. You must abide

by  all  relevant  laws,  health  and  safety  regulations

that apply to the country you are operating in. The

operator's manual instructs you on the machine, its

controls  and  its  safe  operation;  it  is  not  a  training

manual.  If  you  are  a  new  operator,  get  yourself

trained in the skills of using a machine before trying

to work with it. If you don't, you will not do your job

well, and you will be a danger to yourself and others.

In some markets and for work on certain jobsites you

may be required to have been trained and assessed

in accordance with an operator competence scheme.

Make  sure  that  you  and  your  machine  complies

relevant  local  laws  and  jobsite  requirements  -  it  is

your responsibility.

Care and Alertness

All the time you are working with or on the machine,

take care and stay alert. Always be careful. Always

be alert for hazards.

Clothing

You  can  be  injured  if  you  do  not  wear  the  correct

clothing.  Loose  clothing  can  get  caught  in  the

machinery.  Keep  cuffs  fastened.  Do  not  wear  a

necktie or scarf. Keep long hair restrained. Remove

rings, watches and personal jewellery.

Alcohol and Drugs

It is extremely dangerous to operate machinery when

under  the  influence  of  alcohol  or  drugs.  Do  not

consume  alcoholic  drinks  or  take  drugs  before  or

while  operating  the  machine  or  attachments.  Be

aware of medicines which can cause drowsiness.

Feeling Unwell

Do  not  attempt  to  operate  the  machine  if  you  are

feeling unwell. By doing so you could be a danger to

yourself and those you work with.

Mobile Phones

Switch  off  your  mobile  phone  before  entering  an

area with a potentially explosive atmosphere. Sparks

in  such  an  area  could  cause  an  explosion  or  fire

resulting in death or serious injury.
Switch off and do not use your mobile phone when

refuelling the machine.

Lifting Equipment

You can be injured if you use incorrect or faulty lifting

equipment. You must identify the weight of the item to

be lifted then choose lifting equipment that is strong

enough and suitable for the job. Make sure that lifting

equipment is in good condition and complies with all

local regulations.

Raised Equipment

Never walk or work under raised equipment unless

it is supported by a mechanical device. Equipment

which is supported only by a hydraulic device can

drop  and  injure  you  if  the  hydraulic  system  fails

or  if  the  control  is  operated  (even  with  the  engine

stopped).
Make sure that no-one goes near the machine while

you install or remove the mechanical device.

Raised Machine

Never  position  yourself  or  any  part  of  your  body

under  a  raised  machine  which  is  not  correctly

supported. If the machine moves unexpectedly you

could become trapped and suffer serious injury or be

killed.

Lightning

Lightning can kill you. Do not use the machine if there

is lightning in your area.

Machine Modifications

This  machine  is  manufactured  in  compliance  with

prevailing  legislative  requirements.  It  must  not  be

altered in any way which could affect or invalidate its

compliance. For advice consult your JCB dealer.

Summary of Contents for 411HT




















































Reviews: