background image

14

21-18JS

Instruction & User Manual

Inserting the Saw Blade

Prior to any assembly and adjustment always 
unplug the tool/remove the battery pack as 
appropriate.

WARNING!

Only use T-shank jig saw blades.

NOTE

 

m

Pull up the blade fixture and slide the saw 
blade into the groove as far as it will go with 
the blade teeth pointing forward. Make sure 
that the lug of the blade is fitted into the 
blade clamp, then release the blade fixture.

 

m

Ensure the blade is seated correctly in the 
blade guide roller.

 

m

Check the blade is held firmly.

After a cut the saw blade will be very hot. Be 
careful when removing the saw blade. Wear 
appropriate safety gloves.

WARNING!

Power Switch

Before engaging the ON/OFF switch, check 
that the saw blade is properly fitted.

WARNING!

 

m

To power on the jig saw, press and hold the 
safety interlock switch in and then press the 
ON/OFF switch on.

 

m

When you release the ON/ OFF switch the 
tool turns off.

Startup

 

m

Before switching on the jig saw the front 
of the base plate must lie flat on the work 
piece.

 

m

Always hold the jig saw firmly with both 
hands. Make sure that the saw blade is not 
in contact with the work piece before the jig 
saw is turned on.

 

m

Allow the blade to come to a full stop 
before removing it from the cut.

Do not let the jig saw run in continuous 
operation at the lowest speed. The motor 
can overheat.

NOTE

Mitre Cutting

 

m

For mitre sawing and flush-edge sawing the 
base plate can be angled toward either side 
in fixed steps (0°, 15°, 30° and 45°).

Only set the mitre angle when the tool is 
stopped and the blade has stopped moving.
Otherwise the tool can be damaged.

WARNING!

 

m

Open the base plate locking lever. 

 

m

Tilt the base plate to the required position.

 

m

Close the base plate locking lever to lock 
the base plate into position. 

When adjusting the base plate, make sure 
the forward and the rear locating teeth in the 
jig saw body are aligned and fully engaged 
in the corresponding slots in the base plate 
before closing the locking lever.

WARNING!

2825 21-18JS Jig Saw Manual.indd   14

2825 21-18JS Jig Saw Manual.indd   14

08/07/2021   14:48

08/07/2021   14:48

Summary of Contents for 21-18JS





















Reviews: