JBL VLA-C-SB2 Installation Manual Download Page 6

JBL Professional, 8500 Balboa Blvd, Northridge, CA 91329                                                              Rev A- -06/2020 

 

Figure 13 

 

 

Figure 14 (0°) 

 

 

Figure 15 (15°) 

 

Step 15: 

Re-attach the Side-Panel External Trim 
Cover Panels to the side plates of the 
speaker using the same 8-32x1/2

” 

trusshead screws. Apply Loctite 
Threadlocker Blue 242 or equivalent to 
screws before re-attaching (

Refer to VLA-

C Series users guide).

 

 
Step 16: 

Check all screws and attachment 
connections before hoisting speaker 
cluster. 
 
 
 
 
 
 
 

VLA-C-SB2 for VLA-C-125S 
Subwoofer Suspension 

 

Step 17.  

Remove the Side-Panel External Trim 
Cover Panels from the speaker 
(Refer to VLA-C Series users guide). 
Hold onto the screws for later use. 
 

Step 18: 

Attach the (VLA-C-SB2) bracket on 
the VLA-C125S Subwoofer using the 
provided M10 hex bolts, flat washers, 
and split lock washers.  

(Figure 14 = 0°) 
(Figure 15 = 15°) 
(Figure 16 = 30°) 
(Figure 17 = 45°) 
 
Warning: 
Do not use 90° bracket setting when 
VLA-C125S is at the top of the array. 

 

Step 19: 

Tighten screws permanently. 

Reference Torque = 30-35 ft/lb

  

 
 
 
 
 
 
 
 
 
 

Summary of Contents for VLA-C-SB2









Reviews: