background image

4

SPEAKER PLACEMENT

SUBWOOFER

SURROUND SPEAKERS

   5 – 6 ft

    1.5 – 1.8m

FRONT 
SPEAKERS

(0-2 ft)

0-0.6m

The front speakers should be
placed the same distance
from each other as they are
from the listening position.
They should be placed at
about the same height from
the floor as the listeners’
ears will be, or they may be
angled toward the listeners.

The center channel speaker
should be placed slightly
behind the front left and right
speakers, and no more than
two feet above or below the
tweeters of the left and right
speakers. It is often con-
venient to set the center
speaker on top of the tele-
vision set, as shown in the
drawing. 

The SCS300.7 speaker 
system may be used in 5.1-,
6.1- or 7.1-channel applica-
tions. In 5.1-channel applica-
tions, two of the surround
speakers should be placed
slightly behind the listening 

position and, ideally, should
face each other and be at a
level higher than the listeners’
ears. If that is not possible,
they may be placed on a wall
behind the listening position,
facing forward. In 6.1-channel
applications, two of the sur-
round speakers should be
placed in the side positions,
and a single surround back
speaker should be placed on
the wall behind the listening
position. In 7.1-channel
applications, place two of the
surround speakers in the side
positions, and place the two
surround back speakers on
the rear wall.

In Dolby* Digital and DTS

®

systems, it is best to aim all
of the speakers (except the
subwoofer) toward the lis-
tening position at about ear-
level height. In systems
where only analog surround
processing (such as Dolby

Pro Logic*) is available, it
may be preferable to aim the
speakers straight out from
the wall to obtain a more dif-
fuse sound.

The low-frequency material
reproduced by the subwoofer
is mostly omnidirectional,
and this speaker may be
placed in a convenient loca-
tion in the room. However,
bass reproduction will be
maximized when the sub-
woofer is placed in a corner
along the same wall as the
front speakers. Experiment
with subwoofer placement
by temporarily placing the
subwoofer in the listening
position and moving around
the room until the bass
reproduction is best. Place the
subwoofer in that location.

CENTER CHANNEL
SPEAKER

Single surround back speaker  

may be used with 6.1 receivers

and processors. 

Alternate placement for surround speakers when only 5.1 channels are used; required
placement for surround back speakers in 7.1-channel systems.

Summary of Contents for SCS300.7













Reviews: