background image

6

Important Safety Note:

The

customer is solely responsi-
ble for proper selection of
mounting hardware not
included with the speakers,
and for proper assembly 
and installation of the wall
brackets, including but not
limited to the selection of
appropriate weight-bearing
supports and proper use of
the bracket. JBL disclaims
any liability for the selection
of mounting hardware
and/or bracket installation.
Be sure to follow these
bracket assembly and instal-
lation instructions carefully.
If you have any questions or
doubts about your ability to
correctly wall-mount the
speakers, consult with your
authorized JBL dealer or
custom installer.

Step 1: Unscrew and remove
the large 

Molded Nut

. If

necessary, use the supplied

Metal Bar 

as a lever by 

inserting it into one of the
holes in the outer edge of
the 

Molded Nut

.

Step 2: Firmly grasp the 

Ball

and Shaft

£

and pull it

straight out of the 

Attach-

ment Plate

¢

. Avoid leaning

it to the side for leverage, as
this may break off a tab.

Step 3: Slide the 

Molded Nut

onto the 

Ball and Shaft

£

with the threaded open-

ing facing the ball. Thread
the 

Metal Nut

¡

all the way

onto the 

Ball and Shaft

£

,

with the star washer side
away from the ball. Refer to
the exploded drawing for the
proper orientation of these
parts.

Step 4: Screw the 

Ball and

Shaft

£

into the 

Threaded

Insert

§

on the back of the

Satellite Speaker

until 

it is fully seated in the

Threaded Insert

§

, but 

do

not

tighten, as you might 

dislodge the 

Threaded 

Insert

§

. Such damage

would not be covered under
the warranty.

Step 5: Tighten the 

Metal

Nut

¡

with the star washer

side between the 

Metal Nut

¡

and the back of the

Satellite Speaker

, using

large needle-nose pliers,
until it is firmly seated
against the back of the

Speaker

and has locked

the 

Ball and Shaft

£

and

the 

Satellite Speaker

together. Note that once the

Metal Nut

¡

is fully tight-

ened, it may embed some
marks on the back of the

Satellite Speaker

.

However, these marks 
will be covered by the 

Metal Nut

¡

.

Step 6: Mount the 

Attach-

ment Plate

¢

into a wood

stud on the wall, using four
#10 pan-head wood screws
at least one inch long (not
supplied) 

. Make sure that

WALL-MOUNTING

1

2

3

4

8

5

1

2

3

4

5

6

7

8

Gently pull the slack out of the
wire and screw the adapter
onto the back of the speaker 
in two places, as shown.

The floor stand adapter
screws may be found in
Hardware Bag B. Use the
larger screw in the upper
screw hole, and the smaller

screw in the lower screw hole.

Screw the floor stand adapter
into the floor stand’s threaded
insert until the speaker is
firmly attached to the stand.
Back off slightly from the fully
tightened position until the
speaker is oriented as desired,
then rotate the thumbwheel at

the bottom of the floor stand
adapter to secure the speaker
to the stand.

+

+

SCS300.5 OM  5/2/06  4:33 PM  Page 6

Summary of Contents for SCS300.5













Reviews: