JBL MR-140 Operation Manual Download Page 4

11

2

Wiring Identification

1

. Select the 

RADIO / CD / AUX  

by pressing the 

"MODE" button (3)

 

in sequence.

2. Track tuning (7)

Search the track on the DISC with      &      buttons. If you press      or      button 
continuously, the track will fast forward or fast rewind. 

3. Play / pause (8)

Push to pause and push again to resume play.

4. Intro Scan (9)

Press this button to hear the first 10 seconds of each track on the disc. 
Press this button again to restore the player to its normal play mode.

5. Repeat Play button (10)

While playing a desired track, press the RPT button to play the track repeatedly. 
Press the RPT button again to return to normal play mode.

6. Random play button (11)

Press the RDM button to play all tracks on a CD in random sequence.
Press the RDM button again to return the player to  normal mode.

Operating the CD Player

Installation Notes

This radio contains four separate power amplifiers. To prevent possible damage 
to these amplifiers please ensure the following:

(Applicable to both 2 and 4 speaker connection)

i) The boat chassis is not used as a loudspeaker ground(-).  
ii) Front and rear loudspeaker connecting wires are not joined together.
iii) Any wires not used when completing a two speaker installation are fully insulated.
Iv) The memory wire (yellow) is connected to a per 12V supply.
v) The power wire (red) is connected via the ignition switch of the boat.

optional hard wired remote
connector

ANT. SOCKET

12P CONNECTOR

(AUTO ANT)

( BACK-UP  B+ )

FUSE

1A

( GROUND )

FUSE

( IGNITION B+ )

BLUE

YELLOW

BLACK

RED

GRAY

GRAY/BLACK

VIOLET

VIOLET/BLACK

( FRONT RIGHT )

( REAR RIGHT )

GREEN

GREEN/BLACK

WHITE

WHITE/BLACK

( FRONT LEFT )

 ( REAR LEFT )

(LINE OUT)

RED

WHITE

Gray

10A

(AUX IN)

RED

WHITE

Black

1

2

7

4

6

8

10

11

12

13

14

5

3

15

PWR

MUT

TUN

A.PS

BND

MOD

IEQ

T/F

HI-POWER 4x45 Watts

COMPACT DISC PLAYER

1

us

p

h

 

 

L

S

O

E

V

L

  

 RPT

RDM

INT

5

6

9

16

Summary of Contents for MR-140









Reviews: