General Controls (In Detail) Continued
To adjust the front-rear speaker balance, first select the fader mode by pressing button (2)
until FADER appears on the display panel. Press VOL +/- (16) within 5 seconds to
adjust the front-rear speaker level as desired. The fader position will be shown by the bars
on the display panel from FADER F10 (full front) to FADER R10 (full rear).
To adjust the EQ selection, first select the EQ mode by pressing button (2) until EQ
appears on the display panel. Press VOL +/- (16) within 5 seconds to select an equalizer
curve from 4 music types (FLAT, CLASSIC, POP, ROCK).
EQ OFF
: Cancel the sound feature.
FLAT
: Normal operation mode.
CLASSIC : For the dramatic depth of classical music in an auditorium.
POP
: For the electric excitement of stadium pop.
ROCK
: For the subtle extension of the music.
When the SEL button (2) is held over 2 seconds, the unit will
I-VOL is the volume level the unit will play
To adjust
the I-VOL level, first select the I-VOL mode by pressing button (2) until I-VOL appears
on the display panel. Press VOL +/- (16) within 5 seconds to adjust the I-VOL level
from a minimum of I-VOL 00 to a maximum of I-VOL 45. This feature controls the max
volume level desired when powering the unit on.
To adjust the area selection, first select the area mode by pressing button (2) until AREA
appears on the display panel. Press VOL +/- (16) within 5 seconds to select between EUR
and USA.
d. FADER Control
e. EQ Control
a. I-VOL Control
b. AREA Control
enter into a submenu.
Once entered, a single press of the SEL button will result in the following functions:
when the unit is first turned on.
This JBL unit also incorporates memory
retention. For example, if you power the boat off at volume 45 and your initial volume
setting was at 30, the unit will turn back on at 30. If however, you power the boat off at
volume 15 and your initial volume setting was at 30, the unit will turn on at 15. The JBL
unit will always remember the lowest volume as a way of protecting your hearing.
2-2. I-VOL, AREA, BEEP 2ND, SUB W, BT VOL Selection
I-VOL --> AREA --> BEEP 2ND --> SUB W --> BT VOL
c. BALANCE Control
To adjust the left-right speaker balance, first select the balance mode by pressing button
(2) until BALANCE appears on the display panel. Press VOL +/- (16) within 5 seconds
to adjust the left-rear speaker level as desired. The balance position will be shown by the
bars on the display panel from BALANCE L10 (full left) to BALANCE R10 (full right).
8
9
d. SUB-W Control
e. BT-VOL Control
3. VOLUME Control (16)
4. MODE Selection (3)
5. CLOCK/TIME Adjustment
6. LOUD Control
To adjust the sub-woofer mode, first select the SUB-W mode by pressing button (2) until
SUB-W appears on the display panel. Press VOL+/- (16) within 5 seconds to select
between SUB-W ON and SUB-W OFF.
BT-VOL is the default volume level for BT MUSIC mode To adjust the BT-VOL level,
first select the BT-VOL mode by pressing button (2) until BT-VOL appears on the
display panel. Press VOL +/- (16) within 5 seconds to adjust the BT-VOL level from a
minimum of BT-VOL 00 to a maximum of BT-VOL 45.
Press volume up or down button (16) to increase or decrease volume. Current volume
setting is briefly indicated on the display panel form 00 to 45.
Press MODE button (3) to cycle through available program sources as follows:
Radio --> USB --> AUX --> BT MUSIC.
In Radio mode, press DIS button (12) once to display the time.
A. Press and hold the DIS (12) button until time flashes on the display.
B. Press VOL up (16) to set hour.
C. Press VOL down (16) to set minute.
D. Press the DIS (12) button again quickly to accept the adjusted time.
If no button is pressed within 5 seconds, then the unit would automatically accept
the adjusted time without further intervention from the user.
When listening to music at low volume levels, this feature will boost the bass and treble
response. This action will compensate for the reduction in bass and treble performance
experienced at low volume. Press the LD button (14) once to turn LOUD ON, LOUD
icon would appear on the display panel. Press the LD button (14) once again to turn
LOUD OFF, and LOUD icon would disappear from display panel.
.
A valid USB drive must be inserted into the USB port in order for that mode to appear.
Note:
C. BEEP Control
To adjust the beep mode, first select the beep mode by pressing button (2) until BEEP
appears on the display panel. Press VOL +/- (16) within 5 seconds to select between
BEEP 2ND, BEEP ON, and BEEP OFF. Select BEEP 2ND when you wish to hear BEEP
sound whenever any button is pressed for more than 2 seconds. Select BEEP ON when
you wish to hear BEEP sound whenever any button is pressed. Select BEEP OFF then
no beep sound would be heard.
Controls (In Detail) Continued
