JBL DCR600 Service Manual Download Page 9

Page: 9 / 125

Input Source Selector:

Press this button

to change the input by scrolling up or down
through the list of input sources. When an
audio source is selected, the last video input
used remains routed to the

Video 1 Output

and

Video Monitor Output

‚

. This permits

you to simultaneously view and listen to
different sources.

FM Mode Selector:

Press this button to

select Auto or Manual tuning. When the but-
ton is pressed so that the

AUTO

indicator

lights, the tuner will search for the next station
with an acceptable signal when the

Tuning

Selector

is pressed. When the

button is pressed so that the

AUTO

indicator

is not lit, each press of the

Tuning Selector

will increase the frequency.

NOTE:

When the FM reception of a station is

weak, audio quality will be increased by
switching to Mono mode by pressing the

FM (Tuning) Mode Button

until the

STEREO Indicator

goes out.

Digital Optical 2 Input:

Connect the

optical digital output of an audio or video
product to this jack. When the Input is not in
use, be certain to keep the plastic cap installed
to avoid dust contamination that might
degrade future performance.

Digital Coax 3 Jack:

This jack is used for

connection to the output of portable audio
devices, video game consoles or other products
that have a coax digital jack.

Video 4 Video Input Jacks:

These jacks

may be used for temporary connection to the
composite or S-Video output of video games,
camcorders or other portable video products.

Video 4 Audio Input Jacks:

These

audio/video jacks may be used for temporary
connection to video games or portable
audio/video products such as camcorders and
portable audio players.

Bass Control:

Turn this control to modify

the low-frequency output of the left/right
channels by as much as ±10dB. Set this control
to a suitable position for your taste or room
acoustics.

Balance Control:

Turn this control to

change the relative volume for the front
left/right channels.

NOTE:

For proper operation of the surround modes
this control should be at the midpoint, or
“12 o’clock,” position.

(

Treble Control:

Turn this control to modify

the high-frequency output of the left/right
channels by as much as ±10dB. Set this control
to a suitable position for your taste or room
acoustics.

Volume Control:

Turn this knob clockwise

to increase the volume, counterclockwise to
decrease the volume. If the DCR600 is muted,
adjusting the volume control will automatically
release the unit from the silenced condition.

Set Button:

When making choices during

the setup and configuration process, press this
button to enter the desired setting as shown in
the

Main Information Display

into the

DCR600’s memory. The Set button may also be
used to change the display brightness, to avoid
interfering with video presentations:

Press and hold the

Set Button

on the front

panel for three seconds until the message in
the

Main Information Display

reads

VFD FULL

. Within five seconds, press the

front panel

Selector Buttons

until the

desired brightness display level is shown.
Press the

Set Button

again to enter the

setting.

When

FULL

appears in the

Main

Information Display

, the display is at its

normal brightness. When

HALF

appears, the

display is at half the normal brightness level.
When

OFF

appears, all of the indicators in

the

Main Information Display

will go

dark. Note, however, that the

Power

Indicator

will always remain lit to remind

you that the unit is turned on.

Once the desired brightness level is selected,
it will remain in effect until it is changed again
or until the unit is turned off.



Delay:

Press this button to begin the

sequence of steps required to enter delay time
settings.

Digital Input Selector:

When playing a

source that has a digital output, press this
button to select between the

Optical

and

Coaxial

Digital

inputs.

Main Information Display:

This display

delivers messages and status indications to
help you operate the receiver.

Channel Select Button:

Press this button

to begin the process of trimming the channel
output levels using an external audio source.

Speaker Select Button:

Press this button

to begin the process of selecting the speaker
positions that are used in your listening room.

Test Tone Selector:

Press this button

to begin the process of adjusting the channel
output levels using the internal test tone as
a reference.

Remote Sensor Window:

The sensor

behind this window receives infrared signals
from the remote control. Aim the remote at
this area and do not block or cover it unless an
external remote sensor is installed.

DCR600