background image

13

13

13

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

PORT

1

PEDAL

2

C115

C11

C105 /

C105 / C115

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

PORT

1

PEDAL

2

C115

C11

C105 /

C105 / C115

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

NAU

Control Unit

PORT

2

ROBOT

PEDAL

2

Maintenance

Before carrying out maintenance, always switch the device off and disconnect it from the mains. 
Allow the equipment to cool down. 

- Clean the station screen with a glass 

cleaner or a damp cloth. 

- Use a damp cloth to clean the casing and 

the tool. Alcohol can only be used to clean 
the metal parts.

- Periodically check that the metal parts of 

the tool and stand are clean so that the 
station can detect the tool status.

- Maintain tip surface clean and tinned prior 

to storage in order to avoid tip oxidation. 
Rusty and dirty surfaces reduce heat 
transfer to the solder joint.

- Periodically check all cables and tubes.

- Replace any defective or damaged pieces. 
  Use original JBC spare parts only.

- Replace a blown fuse as follows:

1.

 Pull off the fuse holder and remove the  

  fuse. If necessary use a tool to lever it off.

2. 

Press the new fuse into the fuse holder  

  and replace it in the station.

- Repairs should only be performed by a JBC authorized technical service.

Fuse holder

Fuse holder

Fuse

www.jbctools.com

Summary of Contents for NAN





















Reviews: