background image

This product should not be thrown in the garbage. 
In accordance with the European directive 2002/96/EC, electronic equipment at the end of its life 
must be collected and returned to an authorized recycling facility.

Warranty

JBC’s 2 year warranty covers this equipment 
against all manufacturing defects, including the 
replacement of defective parts and labour.
Warranty does not cover product wear or misuse. 
In order for the warranty to be valid, equipment 
must be returned, postage paid, to the dealer 
where it was purchased. 

Please register your 

product warranty within 30 days of purchase 
in www.jbctools.com/productregistration.

Specifications

LC-2SIA

  230V 50/60Hz. Input fuse: 1A. Output: 23.5V

- Weight:

1,95 kg (4.30  lb)

- Dimensions:

128 x 105 x 130 mm (5.04 x  4.13 x 5.12 in)

- Output Peak Power:

40 W

- Temperature Range:

90 - 450 °C (190 - 840 °F) (± 5%)

- Idle Temp. Stability (still air):

± 1.5 ºC / ± 3 ºF

- Tip to ground resistance:

<2  ohms

- Tip to ground voltage:

<2 mV RMS

- Ambient operating temp:

10 - 40 ºC (50 - 104 ºF)

Complies with CE standards.
ESD protected housing.

00

21

00

3-

021

9

www.jbctools.com

Summary of Contents for LC-2SIA













Reviews: