background image

www.jbctools.com

12

13

Before carrying out maintenance or storage, always allow the equipment to cool. 

- Clean the station screen with a glass cleaner 

or a damp cloth.

Remove the fuse by pulling the black cap.  
If necessary use a tool to lever it off.

Press the new fuse into the holder and 
replace it in the station.

Clean  
periodically

- Use a damp cloth to clean the casing and 

the tool. Alcohol can also be used when 
cleaning the metal parts.

- Periodically check that the metal parts of 

the tool/stand are clean so that the station 
can detect when the tool is in the stand. 

- Maintain tip surface clean and tinned prior 

to storage in order to avoid tip oxidation.  
Rusty and dirty surfaces reduce heat 
transfer to the solder joint.

- Periodically check all cables, tubes and        
   filters to ensure proper solder suction.

Maintenance

 

- Replace a blown fuse as follows:

- Replace any defective or damaged pieces. Use original JBC spare parts only. 

- Repairs should only be performed by a JBC authorized technical service.

  It is imperative to follow safety guidelines to prevent electric  
  shock, injury, fire or explosion. 

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause 
fire. 
 
- The power cord must be plugged into approved bases. Be sure that it is properly grounded  
before use. When unplugging it, hold the plug, not the wire.
 
-  Do not work on electrically live parts. Antistatic handle of soldering irons is electrically 
conductive. 
 
- The tool should be placed in the stand when not in use in order to activate the sleep mode.  
The soldering tip, the metal part of the tool and the stand may still be hot even when the station is 
turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on. 

-  Do not cover the ventilation grills. Heat can cause inflamable products to ignite even when  
out of  sight. 
 
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation. 
 
- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when 
working to avoid personal harm. 

- Utmost care must be taken with liquid tin waste which can cause burns. 

- This appliance can be used by children over the age of eight and also persons with reduced 
physical, sensory or mental capabilities or lack of experience provided that they have been given 
adequate supervision or instruction concerning use of the appliance and understand the hazards 
involved. Children must not play with the appliance. Maintenance shall not be carried out by 
children unless supervised.

Safety

Summary of Contents for CSV-2D










Reviews: