background image

10

CD-SC / 

PRECISION SOLDERING STATION

MAINTENANCE

Before carrying out maintenance or storage, always allow the equipment to cool.

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.  
 
- Maintenance shall not be carried out by children unless supervised.

Remove the fuse by pulling the black cap. Help 
yourself with a lever tool if necessary.

Place the new fuse into the holder by pushing 
and enter it again into the station.

Clean periodically

- Clean the station’s screen with a glass cleaner or 
  a damp cloth.

- Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.  

Rusty and dirty surfaces reduce heat transfer to the solder joint.

- Periodically check all cables and tubes connected.

- Replace the fuse if it is blown according to the following guidelines:

- Use a damp cloth to clean the case and the 

tool. Alcohol can be used only to clean the 
metal parts.

- Check periodically that the metal parts of the 

tool/stand are clean in order to have a good 
detection when the tool is in the stand.

Summary of Contents for CD-SC













Reviews: