background image

8

9

Before carrying out maintenance, always allow the equipment to cool. 

- Clean the station screen with a glass cleaner 

or  a damp cloth.

Clean  
periodically

- Use a damp cloth to clean the casing and 

the tool. Alcohol can only be used to clean 
the metal parts.

- Periodically check that the metal parts of 

the tool and stand are clean so that the 
station can detect the tool status. 

- Maintain tip surface clean and tinned prior 

to storage in order to avoid tip oxidation.  
Rusty and dirty surfaces reduce heat 
transfer to the solder joint.

- Periodically check all cables and tubes.

Maintenance

1.

 Pull off the fuse holder and remove the  

    fuse. If necessary use a tool to lever it off.

2. 

Press the new fuse into the fuse holder  

    and replace it in the station.

 
- Replace a blown fuse as follows:

- Replace any defective or damaged pieces. Use original JBC spare parts only. 

- Repairs should only be performed by a JBC authorized technical service.

  It is imperative to follow safety guidelines to prevent electric  
  shock, injury, fire or explosion. 

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. 
 
- The power cord must be plugged into approved bases. Be sure that it is properly grounded  
  before use. When unplugging it, hold the plug, not the wire.
 
-  Do not work on electrically live parts. 

- The tool should be placed in the stand when not in use in order to activate the sleep mode.  
  The soldering tip, the metal part of the tool and the stand may still be hot even when the station is  
  turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on. 

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite. 
 
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation. 
 
- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when  
  working to avoid personal harm. 

- Utmost care must be taken with liquid tin waste which can cause burns. 

- This appliance can be used by children over the age of eight and also persons with reduced 
  physical, sensory or mental capabilities or lack of experience provided that they have been given  
  adequate supervision or instruction concerning use of the appliance and understand the hazards  
  involved. Children must not play with the appliance. 

- Maintenance must not be carried out by children unless supervised.

Safety

www.jbctools.com

Summary of Contents for BT-A








Reviews: