manualshive.com logo in svg

JB Systems PIXEL PIPE, Operation Manual, Page: 9 / 16

Share
Download
JB Systems PIXEL PIPE Operation Manual Download Page 9

ENGLISH 

USER MANUAL 

 

 
JB SYSTEMS

®

 

7/11 

PIXEL PIPE

 

 
[FS00-FS15] Strobe 

Use this function for strobe effect. 
Use 

the ▲ or ▼ buttons for adjusting the speed between slow (FS00) and fast (FS15). 

 

[SU00-SU32] Sound mode 

Use this function to activate the sound mode.. 
Use 

the ▲ or ▼ buttons for adjusting the sensitivity between not (SU00) and very sensitive (SU31). 

 

[AUtO] Automatic mode 

Use this function to put the fixture in an automatic running mode. 
 

[SP01-SP99] Speed  

Use this function to set the speed. 
Use the ▲ or ▼ buttons to select the desired speed from slow (SP01) to fast (SP99). 
 

[don-doFF]   

This function leaves the display on or off during use. 
Use the ▲ or ▼ buttons to select the desired mode: 
 

[don] : display on. 

 

[doff] : display off. 

 

[Iron-IroF]   

This function is used to enable or disable the IR remote control. 
Use the ▲ or ▼ buttons to select the desired mode: 
 

[don] : IR remote control enabled. 

 

[doff] : IR remote control disabled. 

 

[Stnd-rev]   

This function is used to inverse the display. 
Use the ▲ or ▼ buttons to select the desired mode: 
 

[Stnd] : normal display. 

 

[rev] : inversed display. 

 

[dEFA]   

This function is used to reset the fixture to its default factory settings. 
Select [dEFA], the display is blinking. 
Press 

the ▲ or ▼ buttons at the same time to reset the fixture to the default factory settings. 

 

 

OPERATING INSTRUCTIONS 

A.  Standalone 1unit: 

•

  Just connect the projector to the mains. 

•

  Select one of the automatic, sound or static color modes  

•

  Refer to chapter HOW TO SETUP to learn how to make the settings. 

 

B.  Two or more units in master/slave setup: 

•

  Connect the 

units together. Refer to the chapter “electrical installation” to learn how to do this.  

•

  Select one of the automatic, sound or static color modes on the master (the first projector in the DMX 

chain) 

•

  Set all the other projectors in SLAVE mode 

•

  The projectors will now follow the program of the master projector so they all work synchronously. 

NOTE: you can use the wireless remote controller to select the functions on the master unit. The slaves 
will follow. 
 

Summary of Contents for PIXEL PIPE

















Reviews:

No comments