ENGLISH
OPERATION MANUAL
JB SYSTEMS®
3/24
LM140
FUNCTIONS
(FRONT)
Important to know is that you can use this device in
2 ways
:
As a Light Modulator: ALL DIP-switches must be in OFF position. Then you can use this unit
to control lamps and projectors.
As a Switch Pack: you set the DIP-switches (see number 8 for more information ). You can use
a DMX-controller to switch projectors/small light effects ON/OFF. When you use this device as
a Switch Pack, controls 2 to 7 are disabled.
1.
Power Switch:
used to turn the unit ON/OFF.
2.
Flash Buttons:
Press the flash buttons to set the output of the corresponding channels to maximum.
The LEDs display the state of the channels.
3.
Audio/Chase Button:
You can switch between the 2 modes:
Red LED is lit:
the Audio Chase mode is activated. The built-in chase programs are activated by
sound.
Green LED is lit:
the Static Chase mode is activated. The speed of the built-in chase programs
is controlled by the speed knob ( see number 4 for more information ).
4.
Speed Knob:
Used to adjust the speed of the channels when you use the unit in Static Chase mode.
5.
Program Knob:
Used to choose one of the built-in programs.
ENGLISH
OPERATION MANUAL
JB SYSTEMS®
4/24
LM140
6.
Sensitivity Knob:
Used to adjust the sensitivity of the built-in microphone when you are working in
Audio Chase mode.
7.
Stand By Button:
Used to blackout the unit
8.
DMX Adresses:
To set the DIP-Switches, refer to the dmx values below to set the correct address.
On the front of the LM140 you will see that each of the first 9 DIP-switches corresponds to a certain
DMX-value (DIP-switch 10 is not used):
You can combine the values of these switches to obtain any starting address between 1 and 512:
Begin address = 01
switch 1=ON
values: 1
Begin address = 05
switch 1+3=ON
values: 1+4 = 5
Begin address = 09
switch 1+4=ON
values: 1+8 = 9
Begin address = 13
switch 1+3+4=ON
values: 1+4+8 = 13
…
Begin address = 62
switch 2+3+4+5+6=ON
values: 2+4+8+16+32 = 62
Important:
When you use the unit as a switch pack, the light effect/projector will be switched off in the
range from 0-111 ( the corresponding Channel LED is NOT lit ). The light effect will be switch on in the
range from 111-255 ( the corresponding Channel LED is lit ).
FUNCTIONS
(REAR)
1.
DMX-input Connector
2.
DMX-output Connector
3.
Fuse holder Mains input
4.
Channel Output fuses
5.
Channel Outputs:
These outputs are equipped with IEC sockets.
6.
Mains Cable
SPECIFICATIONS
Power Input:
AC 230 V ~ 50 Hz
Channel Output fuses:
6.3 A /250V (5 x 20 mm)
Maximum power per channel:
1200W
Total Maximum power:
3600 W
Mains Fuse:
1 A / 250 V (5 x 20 mm)
DMX input/output:
3pin XLR
Audio input:
None, internal microphone
Size:
482 x 160 x 44 mm
Weight:
1,8 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
Dip
#1
#2
#3
#4
#5
#6
#7
#8
#9
Value
1
2
4
8
16
32
64
128
256
