![background image](http://html1.mh-extra.com/html/jayco/embark-2022/embark-2022_owners-manual_3570511043.webp)
37
Section 4: Vehicle Operation
2. Locate the yellow or white wires with spade termi-
nals and a label identifying them as the Program
Wires.
3. Bend the paperclip, put one end into the spade ter-
minal for the white wire, and the other end into the
spade terminal for the yellow wire.
4. The keypad will beep for
3 seconds.
5. Pull the paperclip out of both wires
before the key-
pad stops beeping.
The keypad is now in “Learn
Mode”.
6. Enter a new 5-digit Authority Code. Each time you press a number on the keypad it will
double beep. When you enter the fifth digit, the keypad will chirp (3) times.
7.
Re-enter the Authority Code for confirmation.
A long beep indicates a failure to
change the code.
8.
Test the new code to confirm it.
9. You have (2) minutes to complete this procedure. If you do not complete the process
within with in the time limit, or if an error is made, the system will exit Learn Mode and
a long chirp will sound indicating an error.
10. The keypad automatically leaves Lean Mode when the new code is set.
Assigning a new Access Code (Authority Code must be programmed first)
1. Press the (5/6) or third button for (5) seconds until the keypad beeps. The keypad back-
light will flash indicating the keypad is in “Learn Mode”.
2. Enter the 5-digit Authority Code. If a correct Authority Code is entered, the keypad
provides a constant beep that only stops when you assign a defined Memory Bank to
store the new Access Code.
•
If you enter an incorrect Authority Code the keypad beeps for (1) second and leaves
the “Learn Mode”.
3. Press and release the button that corresponds to the Memory Bank. For example, press
(1/2) or the first button for Memory Bank #1, press (3/4) or the second button for
Memory Bank #2. There are (4) Memory Bank locations corresponding to buttons
(1/2), (3/4), (5/6) and (7/8).
4.
Enter a 5-digit Access Code. The keypad chirps (3) times after you enter the fifth digit.
5.
Re-enter the new Access Code for confirmation. The keypad chirps (3) times to con
-
firm. A long beep indicates a failure to change the code.
6.
Test the new code to confirm a successful change.
•
Up to (4) Access Codes can be assigned at any time.
•
Adding codes to Memory Bank positions with pre-existing codes will over write
the previous code.
•
If an error is made at any point, or if the time runs out, the keypad will exit “Learn
Mode”, beep for 1-2 seconds and not change anything.
NOTE:
Press the keypad only once regardless of whether you are se
-
lecting the first or the second digit on the keypad. For instance you would
only press keypad (1/2) one time regardless whether you were selecting
the 1 or the 2.
Program Wires
Table of Contents
Maintenance Record
Summary of Contents for Embark 2022
