Jay-Lor 4000 TWIN AUGER Series Operator'S Manual Download Page 53

Page: 53 / 57

AAA-055-00084

Jaylor Operator’s Manual

- 52 -

Twin Auger Trailer Units

4990 Trailer Cutter-Mixer-Feeder

MODEL

4990 TRAILER CUTTER-MIXER-FEEDER

Main Component

Detail

Specification

Mixing Chamber

Capacity

1014 cu.ft. (28.7 m

) (w/ Standard 16” Ext.)

Auger Assembly

Features

Complete w/ 7 Tungsten Carbide Cutter
Blades per Auger

Speed

41 revolutions per minute (RPM)

Frame

Features

- Heavy duty, with provision for 3-point
weigh scale system (standard model)
- Heavy duty, with provision for 5-point
weigh scale system (HD model)

Wheel Assembly

(4) Tire and Wheel
Assemblies

- 15.0 x 17 - 16 Ply Alliance Tire on 17 x 13,
8 Bolt 6000 lb. Rim with Valve Guard
(standard model)
- 445/50R22.5 – 20 Ply Firestone on 22.5 x
13, 10 Bolt, 14000 lb. Rim (HD model)

Hub Assembly

(4) Hub Assemblies

- 8,000 lb. Farm Implement Hub w/ Grease
Lubrication (standard model)
- 12,000lb. Farm Implement Hub w/ Grease
Lubrication (HD model)

Conveyor
Assembly

Width and Type

36” (91 cm) wide, chain/slat discharge,
various option packages available

Conveyor Drive
Assembly

Hydraulic Orbit Motor, 7.5 cu.in/rev.

Drivetrain

PTO Shaft

#8, 1000 RPM operating speed. 1-3/4” dia.,
20 Spline hookup to tractor

Maximum Operating
Speed

1000 revolutions per minute (RPM)

Horsepower
Requirement

165 HP Minimum; depends on commodities
mixed.

Hydraulics

Tractor Hydraulic
System
Requirements

Minimum of 2 sets of Remote Hydraulic
Outlets.
5 GPM (19 L/min) at 2000 psi (13,750 kPa)

Weight

13500 lbs. (6123 kg)

Dependent on equipped options.

* - Due to continual product development, specifications are subject to change without notice.

Summary of Contents for 4000 TWIN AUGER Series


























































Search results

Summary of Contents for 4000 TWIN AUGER Series

Reviews:

Related manuals for 4000 TWIN AUGER Series

Brands by name

Popular brands

Jay-Lor 4000 TWIN AUGER Series, Operator'S Manual

Search results

Summary of Contents for 4000 TWIN AUGER Series

Reviews:

Related manuals for 4000 TWIN AUGER Series

Brands by name

Popular brands