background image

Javo Standard potting machine manual 

Version 2010-11-1  

 

  Page

 11 

Drill size 

The drill size depends on the size of the plug of the material to be planted. 
 
The drill (B) is fixed in the drill chuck on the drill motor by 2 screws (A). These screws 
must be tightened onto the flat side of the drill sleeve 

The drill plate (C) for the drill has a drill hole with a diameter that is approximately 
10 mm larger than the drill. This drill plate must be fixed to the underside of the drill 
rods (D) with 2 lock nuts. 
 
The depth of the plant hole depends on the position of the drill which is adjustable. 
Adjust the depth by moving the drill (B) in the drill chuck (A). 

 

Note: 

The recommended depth of the drill point below the drill plate is 1-2 cm. 

 

Height of the leveller 
The leveller controls the amount of soil in the pot. The height is adjusted by loosening the screw (A) and then moving 
the leveller (B) up or down.   

Leveller up 

 potting soil more compact in the pot 

Leveller down 

 potting soil looser in the pot 

Starting, normal operation, stopping, emergency stop 

The machine can be started in various ways, depending on how the machine was switched off earlier. The various 
options are explained below.  
 
There are 3 control panels on the machine; on the left, on the right and on the switch panel. 

 

Ensure that the machine is in the correct mode 

(see page 5 "Before 

starting") 

Turn the main switch (D) ON on the front of the panel. 
 
Switch the drill, elevator and pot track ON using switches (A, B & C) 
on the front of the panel. 
 
Push the green push-button on the control panel (left or right) to 
start the machine . 
 

Normal stop 
Push the red stop button on the left or right of the machine. 

Emergency stop 
Push the red emergency stop button on the left or right of the machine or on the lid of the control cabinet to 
activate the Emergency Stop. 

Restart after an emergency stop 

1.

 

Make sure the cause of the emergency stop has been resolved 

2.

 

Close all covers and doors 

3.

 

Pull out the red button on the emergency stop to reset it. 

4.

 

Push the blue reset button on the control cabinet 

5.

 

Push the green push-button on the control panel (left or right) to start the machine

 

 

Summary of Contents for Standaard




















Reviews: