Javad HPT401BT User Manual Download Page 31

Page: 31 / 36

Specifications

Connector Specifications

www.javad.com

1.4. Radio Receiver

Table 4. Receiver Specification

1.5. Compliance

Table 5. Compliance

2. Connector Specifications

2.1. DB15 Connector

This connector provides DB15 connectivity for the HPT401BT with a DB9 for connection to a PC/CE
Device for configuration.

Figure 1. DB15 Fem Connector

Parameter

Detail

Noise Figure

4 dB

Receiver Sensitivity (BER 1x10

-4

, 25 kHz CS)

DBPSK
DQPSK
D8PSK
D16QAM
GMSK

-116 dBm 25kHz / -117 dBm 12.5kHz
-115 dBm 25kHz / -116 dBm 12.5kHz
-110 dBm 25kHz / -111 dBm 12.5kHz
-106 dBm 25kHz / -107 dBm 12.5kHz
-113 dBm 25kHz / -114 dBm 12.5kHz

Dynamic Range

-115 to –15 dBm

Max. Input Signal Level

-10 dBm

Co-channel Rejection

-8 dB for 25 kHz Channel Spacing
-8 dB for 20 kHz Channel Spacing
-12 dB for 12.5 kHz Channel Spacing
-16 dB for 6.25 kHz Channel Spacing

Adjacent Channel Selectivity

70 dB for 25 kHz Channel Spacing
70 dB for 20 kHz Channel Spacing
60 dB for 12.5 kHz Channel Spacing
50 dB for 6.25 kHz Channel Spacing

Parameter

Detail

FCC Part

Industry Canada

RSS-119

R&TTE

ETSI EN 300 113-2; ETSI EN 301 489-5
EN 60950-1:2006

Summary of Contents for HPT401BT




































Search results

Summary of Contents for HPT401BT

Reviews:

Related manuals for HPT401BT

Brands by name

Popular brands

Javad HPT401BT, User Manual

Search results

Summary of Contents for HPT401BT

Reviews:

Related manuals for HPT401BT

Brands by name

Popular brands