Javad HPT204BT Series Operator'S Manual Download Page 39

Page: 39 / 42

Appendix C

www.javad.com

AFETY

ARNINGS

Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with a damp cloth.

• Do not block any of the ventilation openings. Install in accordance with the manufacturer's

instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, or has been dropped.

• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall be

placed on the apparatus.

Summary of Contents for HPT204BT Series










































Search results

Summary of Contents for HPT204BT Series

Reviews:

Related manuals for HPT204BT Series

Brands by name

Popular brands

Javad HPT204BT Series, Operator'S Manual

Search results

Summary of Contents for HPT204BT Series

Reviews:

Related manuals for HPT204BT Series

Brands by name

Popular brands