background image

Getting to Know Your Device 

Packing list 

Upon  receiving  the  product,  please  unpack  the  product  package  carefully.  Each  product  is 

shipped with 

the following items:   

CPE Products 

Quantity 

ODU unit 

Router unit 

Mounting brackets 

48V DC power adapter 

Ethernet cable 

If you find any of the items is missing, please contact our local distributor immediately. 

Unpacking the Equipment 

All the standard parts that are supplied in your LTE CPE Unit Installation Package. Please take 

time to unpack the package and check its contents against this list. 

 

LED Indicators 

Type 

LED 

Function 

Description 

 
 
 
 
 

Router 

SYS 

Power indicator   

Orange Color 

– Device is powered on. 

Blinking green 

– Wireless access not ready.   

Green Color 

– Network is available 

NET 

WAN port status 

Blinking green 

– The data is in transmission. 

SIG 

RF signal indicator 

Reserved function, not being used 
currently. 

2.4G&5G 

Wi-Fi indicator 

Light is on 

–2.4G&5G Wi-Fi is on. 

LAN1&LAN2  LAN port status 

Solid green 

–    LAN port is up. 

Blinking  green 

–  LAN  data  activity  in 

progress. 

 

 

 

Summary of Contents for JT6200M









Reviews: