Jasper A-1DB-N Quick Start Manual Download Page 3

Page

2

of

9

The installer must set up the device according to AS/NZS 5601, local authority, gas and
any other relevant statutory regulations

.

Try to confirm whether the product is fitted in

a non-flammable location near the unit where you can. Approval from flammables walls

sides right and left 350mm, approval from the back of 150mm,

The splashback return can go forcefully against the back wall for the F

series. The installer must look at local structural guidelines on non-flammable constru
ction substance instructions for detail.

You must set up this product with an exhaust mechanism, including a canopy and vent
system. The hood should be designed with a substance that is immune to grease,
moisture and fat. Its internal appearance should be slick and without any roadblocks.
Besides, all the joints shall be adequately tight. One shall locate the canopy so as to
aerate the device efficiently. It shall spread a minimum of 150 mm outside the
boundaries of the device.
Unless properly secured, a vent and a hood shall be installed at least 450 mm from any
flammable substance. It should be done in such a manner that the grease filter's lower
edge is at least 1.5 meters over the product's surface.
Do not install before taking out any transportation packaging for this product.
NOTE: each wok ring has a different regulator. It also has a gas cock on the channel. You
must set up the product as mentioned in the installation guidelines. i.e., Propane or
natural gas checking point pressures.

WATER CONNECTION

500 mm above the floor and approximately 150mm in from right hand side. A 2”
compression fitting is provided for connection. All dime or – 20 mm
The installer to provide a isolating stop tap to the appliance.

WATER DRAINAGE

Placed 70mm in from the right or left side x 200mm down from the tabletop, a 40 mm
(11/2” BSP) galvanised pipe elbow is given for the discharge mechanism.
Before finishing the setup, take a look at all the water & gas installations for leaks.
Besides, direct the operative to handle the device and use it judiciously properly.

approval from the top

of 1500mm.

Summary of Contents for A-1DB-N













Reviews: