background image

 

 

23

 

8. MMA INSTALLATION, DEBUGGING AND OPERATION 

Attention: Please install and debug according to following steps! 

Electrical connection cannot be conducted until distribution box is turned off. 

          Due to IP21S protection class, this machine should not be operated in the rain. 

         

Please refer to No.7 “connection of distribution box”. 

8.1. Installation 

8.1.1. 

Power  cord  (cross-sectional  area  of  copper  conductor  should  be  3*4mm

2

  or  more)  should  be 

connected to junction box as indicated in 7.1.1. 

8.1.2. 

MMA mode is selected. 

8.1.3. 

Cable  plug  with  electrode  holder  should  be  inserted  into 

the  “-”  socket  on  the  front  panel  and  be 

tightened. 

8.1.4. 

Cable plug with earth clamp should be inserted into 

the “+”socket on the front panel and be tightened. 

8.1.5. 

Ground connection is necessary. 

8.1.3 and 8.1.4 refer to  DCSP connection. Operators can select connection method according to 

base  metal  and  electrode  application  requirement.  Generally,  DCRP  connection  is  recommended  for 

basic electrode (cable plug with earth clamp is connected to negative socket), while there is no special 

requirement for acid electrode. 

8.2. Installation diagram 

Summary of Contents for MIG250P































Reviews: