background image

WiFi1500CF Plug-In Hardware User Guide JA03-UM-WiFi

    

 Page 13    Rev: P00    Date: 03/13/14

© Copyright 2014 Janus Remote Communications   

Specifications subject to change without notice

   All Rights Reserved   See website for latest revision.    Not intended for life support applications.

5. Configuration Options

Interface Voltage* 

R22 

R23 

USAGE

2.8 volts (default) 

0 ohm  OMIT 

T2 & 400AP

3.3 volts 

 

OMIT 

0 ohm  user interface

GS1500M Flash programming

CF SERVICE pin 17 pulled low
-- or --
JP1 installed

J2F GPS Flash programming

JP2 installed

GS1500 SPI INTERFACE 
CF PIN 

FUNCTION

GPIO1  

SPI CLK

GPIO2  

SPI CS

GPIO3  

SPI MOSI

GPIO4  

SPIMISO

GPIO5  

SPI WAKEUP

GS1500 I2C INTERFACE 
CF PIN 

FUNCTION 

USAGE

I2C SCL 

I2C CLK  

install R9 to enable 

I2C SDA 

I2C DATA 

install R10 to enable

     

 

optional pull-up resistors: 

     

 

I2C CLK - 

R21 

 

     

  

I2C DATA - 

R20

J2F GPS I2C INTERFACE 
      

 

 

R9 

R10 

disabled (default) 

OMIT 

OMITt

enabled 

 

0 ohm  0 ohm 

UART TX/RX INTERFACE
WIFI  

GPS 

R14  R15  R16 

R19  R8 

R13  R6 

R7 

R12 

USAGE

UART0 TX/RX @VIO  GPS TX/RX @VIO  0 ohm  0 ohm  OMIT  OMIT  OMIT  OMIT  0 ohm  0 ohm  OMIT 

T2 w [email protected]   

(default)
UART0 TX/RX @VIO  GPS TX/RX @3.3V  OMIT  OMIT  0 ohm  0 ohm  OMIT  OMIT  0 ohm  0 ohm  OMIT 

400AP w [email protected]

disabled  

UART0 TX/RX @VIO  OMIT  OMIT  OMIT  OMIT  0 ohm  0 ohm  OMIT  OMIT  0 ohm  GPS w/ PPS on DCD

* Interface voltage: VIO affects the following CF terminals:

GPIO1  GPIO5 

UART TX 

CELL LED  GPS TX+

GPIO2  GPIO6 

UART RX 

GPS LED 

GPS RX+

GPIO3  GPIO7 

UART RTS  TRACE RX   

GPIO4  UART DCD  UART CTS  TRACE TX    

   + GPS RX/TX can be configured to bypass level shifters 

 

      for use with the 400AP.

GS1500 ADC/DAC INTERFACE
CF PIN 

FUNCTION 

INSTALL

ADC1 

GS ADC1/DAC 

R3

ADC2 

GS ADC2 

R4

DAC 

GS ADC1/DAC 

R5

GS1500 SERIAL ASYNC
CF PIN  FUNCTION 

INSTALL

GPIO7 

ASYNC 

R1

GS1500 drives ASYNC high during asynchronous serial output.

GPS POWER SUPPLY BYPASS

Dedicated GPS low noise supply can be omitted by: 
   Installing: 

FB5

   Removing: 

U8 

FB4

     

R29,R30 

C18,C19,C20,C21

GS1500 STANDBY MODE

Not supported. 

 

 

   Allows placing GS1500 module into a low power 

 

 

mode for a set time period. 

  

5. Configuration Options Notes

Summary of Contents for WiFi1500CF Plug-In

















Reviews: