manualshive.com logo in svg

Janome Skyline S7, Service Manual

Share
Download
Janome Skyline S7 Service Manual Download Page 13

11

Replacing electronic components

DC motor

NOTE:

Do not disconnect  connectors by pulling on cord.

To disconnect the connectors, grasp the connector, 

not the cord.

To remove:

1. Remove the belt cover, the top cover and the front 

  cover (see pages 1, 2 and 5).

2. Disconnect the DC motor connector from the printed 

  circuit board A (see page 8).
3. Remove the motor belt.

4. Remove the setscrews (2 pcs), and the DC motor.

To attach:

1. Attach the DC motor and slightly tighten the setscrews.

2. Attach the motor belt and adjust the belt tension. 

  Push the middle of the belt span with approximately 

  200 grams pressure. Adjust the motor position so that 

  the belt deflects 5 mm.
3. Tighten the setscrews securely.

4. Connect the DC motor connector to the printed circuit 

  board A (see page 7).

5. Attach the front cover, the top cover and the belt cover.

Setscrews

Setscrews

Motor belt

200 gr pressure

5 mm

Summary of Contents for Skyline S7








































Reviews:

No comments

Brands by name

Popular brands

Load more brands