Janome DC 3018 Service Manual Download Page 8 | Manualshive

Page: 8 / 33

Janome DC 3018 Service Manual Download Page 8

SERVICE ACCESS (3-1)

SETSCREW (C)

SETSCREW (B)

SETSCREW (A)

SETSCREW (F)

SETSCREW (E)

SETSCREW (D)

FRONT COVER

SETSCREW (G)

MACHINE SOCKET

(CONNECTOR ON

THE PCB)

POWER

T R A N S F O R M E R

(CONNECTOR ON

THE PCB)

SETSCREW (H)

TO REMOVE:

1. REMOVE THE FACE COVER AND BED COVER (SEE PAGES 7 AND 8).

2. LOOSEN THE SETSCREWS (A), THEN REMOVE THE SETSCREWS (B), (C), (D), (E), (F), (G) AND (H).

3. REMOVE THE FRONT COVER (SEE PAGE 10) AND DISCONNECT EACH SWITCH CONNECTORS.

NOTES

TO DISCONNECT THE CONNECTORS:

1. GRASP THE CONNECTOR DIRECTLY WITH YOUR FINGERS AND PULL. DO NOT PULL ON THE LEAD

WIRE, AS THIS MAY DAMAGE THE CONTACT SLEEVE INSIDE THE CONNECTOR.

2. WHEN DISCONNECTING THE MACHINE SOCKET AND POWER TRANSFORMER

CONNECTORS, PULL THEM WHILE PUSHING THEM TOWARD THE PRINTED CIRCUIT BOARD A TO

UNLOCK THEM.

TO INSTALL:

TO INSTALL THE FRONT COVER, FOLLOW THE ABOVE PROCEDURE IN REVERSE.

NOTES: TO CONNECT THE CONNECTORS:

1. BE SURE THAT THE COLOR OF EACH CONNECTOR CORRESPONDS TO THE COLOR OF THE

CONNECTOR POST ON THE PRINTED CIRCUIT BOARD (PCB) TO WHICH IT IS CONNECTED.

2. INSERT THE CONNECTOR AT THE RIGHT ANGLE. THEN PUSH IT STRAIGHT DOWN UNTIL IT LOCKS

IN PLACE.

6

«
...
6
7
8
9
10
...
»

Summary of Contents for DC 3018


































Reviews:

No comments