manualshive.com logo in svg

Janome DC 3018, Service Manual, Page: 24 / 33

Share
Download
Janome DC 3018 Service Manual Download Page 24

TO REMOVE:

1. REMOVE THE FRONT COVER UNIT (SEE PAGE 6~7).

2. UNPLUG THE SLIDE VOLUME CONNECTOR.

3. REMOVE THE FOUR CS RING  (A) AND REMOVE THE SIDE VOLUME.

TO INSTALL:

4. TO INSTALL THE SLIDE VOLUME, FOLLOW THE ABOVE PROCEDURE IN REVERSE.

  * SECURE THE LEAD WIRE ON THE BOARD USING THE CS RINGS, AS SHOWN.

  * CHECK TO ENSURE THAT THE SLIDE VOLUME MOVES SMOOTHLY BACK AND FORTH.

PRINTED CIRCUIT BOARD "F"

CONNECTOR

PRINTED CIRCUIT

BOARD "F"

SETSCREWS

(2)

REPLACING THE SLIDE VOLUME

REPLACING PRINTED CIRCUIT BOARD "F"

TO REMOVE:

5. REMOVE THE FRONT COVER UNIT.

6. UNPLUG THE PRINTED CIRCUIT BOARD "F" CONNECTOR AND REMOVE THE FOUR CS RINGS.

7. REMOVE THE TWO SETSCREWS  AND REMOVE THE PRINTED CIRCUIT BOARD "F".

TO INSTALL:

   TO INSTALL THE PRINTED CIRCUIT BOARD "F". FOLLOW THE ABOVE PROCEDURE IN REVERSE.

   * SECURE THE LEAD WIRE ON THE BOARD USING THE CS RING, AS SHOWN.

   * EACH BUTTON (NEEDLE UP/DOWN BUTTON, START/STOP BUTTON, REVERSE BUTTON) SHOULD

     "CLICK" WHEN PRESSED.

SLIDE VOLUME

CONNECTOR

REPLACING SLIDE VOLUME AND PRINTED CIRCUIT BOARD F

CS RINGS (4)

CS RINGS (4)

SLIDE VOLUME CONTROL

22

Summary of Contents for DC 3018


































Reviews:

No comments