background image

AAASewing.com

20

01

02

03

04

06

07

08

09

1

2

1

2

1

2

1

2

1

2

1

2

1

2

1

2

Variety of Straight Stitching

Pattern #01        Straight stitch

Foot A: Zigzag foot

For seaming garments, zipper application and more.

Pattern #02

Lock-a-Matic stitch

Foot A: Zigzag foot

Seaming with auto reverse stitches at the beginning and end

Press the reverse stitch button once, the machine will sew the reverse

stitches and stop automatically.

Pattern #03

Locking stitch

Foot A: Zigzag foot

Seaming with auto locking stitches at the beginning and end

Press the reverse stitch button once, the machine will lock the stitches and

stop automatically.

Pattern #04

Stretch stitch

Foot A: Zigzag foot

For seaming stretch fabrics that tend to pucker

The seam can be opened flat.

Pattern #06

Straight stretch stitch

Foot A: Zigzag foot

Strong and durable stitch recommended for stretch fabrics and areas to

reinforce.

Pattern #07

Sculpture stitch

Foot F: Satin stitch foot

For top stitching and outlining designs.

Sew slowly at the corners.

Pattern #08

Stretch stitch

Foot F: Satin stitch foot

For top stitching and quilting.

Pattern #09

Saddle stitch

Foot A: Zigzag foot

Long straight stretch stitch, similar to hand stitches.

1

2

1

2

1

2

1

2

1

2

1

2

1

2

1

2

Janome 6260QC Instruction Manual

Janomesewing machine

www.aaasewing.com

6260QC Owners Manual/ User Guide

Summary of Contents for 6260QC -





















































Reviews: