background image

IMPORTANT  SAFETY INSTRUCT IONS 

This sewing machine is not a toy. Do not allow children to play with this machine. 

T he machine is not intended for use by children or mentally infirm persons without supervision. 

This sewing machine is designed and manufactured for household use only. 

Read all instruction before using this  sewing machine. 

DANGER 

-

To reduce the risk of electric shock: 

1 .   An appliance should never be left unattended when plugged in. Always unplug this sewing 

machine from the electric outlet immediately after using and before cleaning. 

2.  Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 1 5  watts. 

3.  Do not reach for the appliance that has fallen into water. Unplug immediately. 

4. 

Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or 

drop into water or other liquid. 

WARNING 

-

To reduce the risk of burns,  fire,  electric shock, or injury to persons: 

1 .  Do not allow children to play with the machine. T he machine is not intended for use by children or 

infirme persons without proper supervision. 

Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by 

or near children. 

2.  Use this appliance only for its intended use as described in this owner's manual. 

Use only attachments recommended by the manufacturer as contained in this owner's manual. 

3. 

Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it 

has been dropped or damaged, or dropped into water. 

4. 

Never operate the appliance with any air opening blocked. Keep ventilation opening of this sewing 

machine and foot controller tree from accumulation of lint, dust and loosen cloth. 

5.  Never drop or insert any object into any opening. 

6.  Do not use outdoors. 

7. 

Do not operate where aerosol (spray) products are being used or where oxygen is being 

administered. 

8.  To disconnect,  turn all controls to the off ("O") position, then remove plug from outlet. 

9. 

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 

10. 

Keep fingers away from all moving parts. Special care is required around the sewing machine 

needle. 

1 1  .  Always use the proper needle plate. The wrong plate can cause the needle to break. 

2. 

Do not use bent needles. 

1 3.  Do not pull or push fabric while stitching. It may deflect the needle causing it to break. 

14.  Switch this sewing machine off ("O") when making any adjustment in the needle area, such as 

threading the needle, changing the needle, threading the bobbin or changing the presser foot, and 

the like. 

15.  Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or 

when making any other adjustments mentioned in this owner's manual. 

SAVE THESE INSTRUCTIONS 

Please note that on disposal, this product must be safely recycled in accordance with relevant 

National legistlation relating to electrical/electronic products. If in doubt please contact your retailer 

-

for guidance. (European Union only.) 

Summary of Contents for 2200XT































Reviews: