Janome 15822 Page 2 Servise Manual Download

Page: 2 / 25

CONTENTS

WHAT TO DO WHEN ....................................................................................... 3-5

SERVICE ACCESS

FACE COVER ............................................................................................... 6

TOP COVER ................................................................................................. 6

BASE COVER ............................................................................................... 7

REAR COVER .............................................................................................. 8

FRONT COVER ............................................................................................ 9

MECHANICAL ADJUSTMENT

NEEDLE THREAD TENSION .................................................................... 10

BOBBIN TENSION ..................................................................................... 11

PRESSER BAR HEIGHT AND ALIGNMENT ............................................. 12

NEEDLE SWING ........................................................................................ 13

NEEDLE DROP POSITION ........................................................................ 14

CLEARANCE BETWEEN NEEDLE AND SHUTTLE ............................. 15-16

FEED DOG HEIGHT .................................................................................. 17

NEEDLE BAR HEIGHT .............................................................................. 18

NEEDLE TIMING TO SHUTTLE ................................................................. 19

BUTTONHOLE FEED BALANCE ............................................................... 20

DISTORTED PATTERN (MODEL NEXT 40, 30 ONLY) .............................. 21

ADJUSTING BUTTONHOLE LEVER POSITION ....................................... 22

DISENGAGEMENT OF CAM FOLLOWER ................................................ 23

MOTOR BELT TENSION ............................................................................ 24

WIRING ...................................................................................................... 25

PARTS LIST ................................................................................................ 26-43

Summary of Contents for 15822


























Search results

Summary of Contents for 15822

Reviews:

Related manuals for 15822

Brands by name

Popular brands

Janome 15822, Servise Manual

Search results

Summary of Contents for 15822

Reviews:

Related manuals for 15822

Brands by name

Popular brands