background image

4

UMG 96RM-P/-CBM

Instructions for use

Please read the operating manual included in the delivery 
as well as all other publications that must be drawn 
from for working with this product (in particular for 
the installation, operation or maintenance). In doing so 
note that fundamental explanations for commissioning, 
operation and configuration are described in 
the operating instructions for the basic device UMG 
96RM. These instructions describe only the extended 
functions of the specific equipment variant.

Follow all safety regulations and warning information. If 
you do not follow the information, it can result in bodily 
injury and/or damage to the product.

Any unauthorized changes or use of this device, which 
transcend the mechanical, electrical or otherwise stated 
operating limitations, can result in bodily injury and/or 
damage to the product. 

Any of such unauthorized changes constitute "misuse" 
and/or "negligence" in terms of the warranty for 
the product and therefore eliminates the warranty for 
covering any potential damage resulting from this.

c

If the device is not operated according 
to the operating manual, protection is no 
longer ensured and danger can come from 
the device.

m

Single core wires must be provided with 
sleeves.

m

Only pluggable screw terminals with the same 
number of poles and the same type of construction 
are permitted to be connected together.

This device is to be operated and maintained exclusively 
by specialized personnel.
Specialized personnel are persons, that based on their 
respective training and experience, are qualified to 
recognize risks and prevent potential dangers that can be 
caused by the operation or maintenance of the device. 

Additional legal and safety regulations required for 
the respective application are to be following during 
the use of the device.

Summary of Contents for UMG 96RM-CBM

















































Reviews: