Page 11
ENGLISH
Jandy
®
Pro Series, White LED Lights
|
Installation Manual
10. To secure the ground wire, place the flat washer,
followed by the ground wire, followed by the split
washer, securing in place with the nut. Torque to
12 in-lbs.
7.6 Reassemble the Fixture.
1.
If not already done, remove the gasket from the
glass lens and install a new gasket on the lens. On
the small light, remove the diverger from the lens.
NOTE
A new lens gasket must be used each time the light is
reassembled.
WARNING
Risk of Electrical Shock or Electrocution.
Always
install a new lens gasket whenever disassembling the
light. Failure to do so may permit water to leak into the
assembly, which could cause:
(a) An electrical hazard resulting in death or serious
injury to pool or spa users, installers, or others due to
electrical shock, or
(b) A malfunction of the Jandy White LED Light,
which likewise could result in serious injury to pool or
spa users, installers, or bystanders, or in damage to
property.
2.
While holding the fixture upright, place the glass
lens with the gasket on top of the fixture. Please
note that the lens gasket is not symmetrical.
Therefore, it must be installed correctly so that
the lens can seal to the fixture housing. Place the
gasket on the lens with the orientation shown in
Figure 10. On the small light, replace the diverger
by tucking the tabs between the lens and gasket.
NOTE
Be sure to face the dull side of the diverger down
towards the PCB.
3.
Position the lens and gasket on the fixture. Place
the face ring assembly over the lens and align the
pilot screw with the small arrow mark on the face
of the lens. Note that the small arrow mark on
the face of the lens and the pilot screw of the face
ring must be aligned with the arrow located on
fixture label that reads, “Arrow on this label must
line up with the pilot screw on the Face Ring”.
See Figure 9.
4.
While holding the aligned face ring assembly and
fixture together, turn the assembly upside down
and set it on the old gasket, using the old gasket
as an assembly fixture. This will keep the lens
and gasket assembly from being pushed out of the
face ring while you secure it to the light fixture.
5.
Spread the bottom clamp over the electrical cord
and slide it onto the back of fixture to the top
clamp.
6.
Tighten the Phillips head screws (eight (8) for
large light and six (6) for small light) on the light
in alternating cross-pattern. Torque screws to
approximately 25 in-lbs.
7.
Discard the old gasket.
7.7 Reinstall the Jandy Pro Series Light
Into Niche Fixture.
1.
Coil the extra four (4) feet of cord around the
fixture or into the base of the niche and place the
light assembly into the niche.
2.
Engage the retainer tab on the bottom of the face
ring, then pivot the top of the fixture inward and
tighten the special pilot screw.
WARNING
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided could
create an electrical hazard, which could result in death
or serious injury to pool or spa users, installers or
others due to electrical shock.
3.
If pool is empty, Fill the pool until the underwater
light is completely submerged in water before
operating the light for more than 2 minutes. The
light will heat up quickly when operated outside
of water. Turn on main switch or circuit breaker,
and the switch, which operates the underwater
light, to check for proper operation.
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will get
extremely hot, which may result in serious burns or in
damage to the light. This may result in serious injury
to pool or spa users, installers, or bystanders or in
damage to property.
Fixture
Lens
Thick molded
side of the
gasket must
mate with
the body of
the housing
Figure 10. Cross Section of Jandy Pro Series White
LED Light