Page 10
ENGLISH
Jandy
®
Pro Series, White LED Lights
|
Installation Manual
5.
Apply thermal grease to the back of the new LED
board.
6.
Place new LED board into the heat sink with the
orientation shown in Figure 7.
7.
Secure the LED board with two (2) screws and
two (2) washers.
8.
Plug in the board connector.
7.4 120V Small Light Driver (PCB)
Replacement
1.
Disconnect power and wait 5 minutes.
2.
Remove LED board as instructed in step 7.3
3.
Remove 2 screws from the heat sink and remove
the heat sink.
4.
Remove both quick disconnect wires from the
PCB. Note that the black wire is connected to
ACN and the White wire is connected to ACL.
5.
Remove 2 metal posts from the driver board
6.
Remove driver board and place new light driver
board into the fixture with the orientation shown
in Figure 7.
7.
Insert metal posts back on to the screw studs.
8.
Plug in both quick disconnect wires, white onto
the terminal ACL of the light driver and black
onto the ACN.
9.
Align heat sink to the metal posts
10. Secure the heat sink with 2 screws
11. Apply thermal grease to the back of the new LED
board.
12. Place new LED board into the heat sink with the
orientation shown in Figure 7.
13. Secure the LED board with two (2) screws and
six (6) washers.
14. Plug in the board connector.
7.5 Large Light Driver (PCB) Replacement
(120V and 12V)
1.
Disconnect power and wait 5 minutes.
2.
Unplug the quick disconnect terminals and the
grounding wire (green) from the light driver.
3.
Remove three (3) nuts and washers.
4.
Remove the LED board, light driver board and
board connector from the light fixture.
5.
Apply thermal grease to the back of the new LED
board.
6.
Place new LED board and light driver board into
the fixture with the orientation shown in Figure 8.
7.
Secure the new boards with 3 washers, spilt
washers and nuts. Torque to 12 in-lbs.
8.
Plug in the white quick disconnect wire onto the
terminal AC1 (TP-L) of the light driver board.
9.
Plug in black quick disconnect wire onto terminal
AC2 (TP-N) of the light driver. Ensure board
connectors are connected to both boards.
2
Remove the bottom clamp, the face ring
assembly, the glass lens, and the gasket from
the fixture. Remove the silicone gasket from
the lens. Refer to
Section 9, Exploded View and
Replacement Parts
.
WARNING
To minimize risk of damage to the light and risk of
serious injury, including loss of life, ALWAYS install a
new silicone gasket whenever disassembling the light.
7.2 12V Small Light Driver (PCB)
Replacement
1.
Remove both quick disconnect wires from the
PCB. Note that the black wire is connected to
ACN (TP-2) and the White wire is connected to
ACL (TP-1).
2.
Remove two (2) nuts and two (2) washers.
3.
Remove the light driver from the light fixture.
4.
Apply thermal grease to the back of the new light
driver board.
5.
Place new light driver into the fixture with the
orientation shown in Figure 7.
6.
Secure the light driver with one (1) washer and
one (1) nut on the right side of the light driver.
Torque to 12 in-lbs.
1
POOL WALL
Power
Cord Niche
POOL LIGHT
ASSEMBLY
PILOT SCREW
Push up on
bottom of
light
assembly
2
Power
Cord
Niche
SPA LIGHT
ASSEMBLY
SPA WALL
1
PILOT SCREW
Push up on
bottom of
light
assembly
2
Unscrew pilot screw
and pull top of light
assembly away from
spa wall
Bonding
cable
Unscrew pilot screw
and pull top of light
assembly away from
pool wall
Bonding
cable
Figure 6. Removing the Jandy Pro Series White
LED Light Assembly for Light Driver
Replacement
7.
Place a washer on the other stud and place the
green ground wire terminal on the washer and
secure both with the nut. Torque to 12 in-lbs.
8.
Plug in the quick disconnect wire (white) onto the
terminal ACL (TP-1) of the light engine.
9.
Plug in the quick disconnect wire (black) onto
terminal ACN (TP-2) of the light engine.
7.3 120V Small LED Board Replacement
1.
Disconnect power and wait 5 minutes.
2.
Remove two (2) screws and six (6) washers.
3.
Unplug the board connector from the light engine.
4.
Remove the LED board from the heat sink. If
you are also replacing the driver board, you can
proceed now to step 7.4