background image

Page 1 0

C artridge Pool Filters -  C L and C V  S eries Filters

3.5 Clamp Installation

1. 

Be certain the o-ring is in position in the lower 

tank half. Press the filter lid over the lower half 

sandwiching the o-ring between the two halves.

2.  Holding the ends of the filter clamp apart, position 

the hinged segment of the filter clamp over both 

upper and lower tank flanges. Bring the ends of the 

filter clamp together.

3.  Place the "T" nut and threaded rod assembly into 

the clamp. Be sure the "T" nut is seated in the 

clamp in the proper orientation (See Fig. 9).

4.  Use a 9/16" socket on the tightening nut until the 

clamp ring halves touch each other, or are within 

1/16" (See Fig. 9) 

but do not overtighten as the 

clamp can break

. If unable to tighten as indicated, 

do not operate the filter and 

call a service 

technician immediately

.

5.  After the first week of operation, check the clamp 

and retighten if necessary.

6.  Check the filter clamp at least once a month. 

Figure 9 .  

Filter C lamp Ring

Cl a m p  R i n g

" T "  N u t  a n d  
T h r e a d e d  R o d

T i g h t e n i n g  N u t  
w /  S h o u l d e r

2.  Check that the drain plug for CL filters or drain 

cap for CV filters is in place and tight.

3. 

Check that the tank clamp is correctly seated and 
tight (See Figs. 9 and 10).

4.  Open the pump hair/lint pot lid and fill the pump  

basket with water to prime the system. Replace the 
lid. (You may have to do this several times on new 
and seasonal start-ups.)

5. 

Completely open the air release valve on the 

gauge/air release assembly by turning the knob on 

the back of the assembly fully counterclockwise 
(do not remove the knob).

6.  Be sure to open any filter isolation valves that 

were installed in the system.

7. 

Stand clear of the filter 

and start the pump to 

circulate water through the system. When a steady 
stream of water starts to come out of the air release 
valve, close the valve.

8. 

Watch the pressure gauge to be sure that the 
pressure does not exceed 50 psi (with clean 
cartridges). If the pressure approaches 50 psi, 
immediately turn the pump off and clean the 

filter cartridges (see Section 6.3). If the pressure 

remains high after cleaning the filter, refer to the 

troubleshooting guide in Section 8 for possible 
causes and solutions.

           W A RN I N G

F o l l o w  t h e se

 i n st r u ct i o n s  ca

r e f u l l y .  

I m p r o p e r  cl a m p  i n st a l l a t i o n  ca

n  ca

u se

 

t h e  f i l t e r  l i d  t o  b e  b l o w n  o f f ,  w h i ch

 c a n  

r e su

l t  i n  d e a t h ,  se

r i o u s  p e r so

n a l  i n j u r y ,  

o r  p r o p e r t y  d a m a g e .

 C A U T I O N

DO  N O T

 o p e r a t e  f i l t e r  a t  w a t e r  t e m p e r a t u r e s  a b o ve

 

105° F (40.6° C). Water temperatures above the 

m a n u f a ct u r e r ' s  r e co

m m e n d a t i o n s  w i l l  sh

o r t e n  t h e  

l i f e  sp

a n  o f  t h e  f i l t e r  a n d  vo

i d  t h e  w a r r a n t y .

          W A RN I N G

N E V E R

 st a r t  p u m p  w h i l e  st a n d i n g  

within five (5) feet of the filter. Starting 

t h e  p u m p  w h i l e  t h e r e  i s  p r e ssu

r i ze

d  a i r  

i n  t h e  syst

e m  ca

n  ca

u se

 t h e  f i l t e r  l i d  t o  

b e  b l o w n  o f f ,  w h i ch

 ca

n  ca

u se

 d e a t h ,  

se

r i o u s  p e r so

n a l  i n j u r y  o r  p r o p e r t y 

d a m a g e .

 W A RN I N G

N E V E R

 o p e r a t e  t h e  f i l t e r  syst

e m  a t  

more than 50 psi of pressure. Operating 

the filter system in excess of 50 psi can 

ca

u se

 t h e  f i l t e r  l i d  t o  b e  b l o w n  o f f ,  w h i ch

 

ca

n  ca

u se

 d e a t h ,  se

r i o u s  p e r so

n a l  i n j u r y 

o r  p r o p e r t y  d a m a g e .

Section 4. Start-Up and Operation

N O T E

 

T h i s  se

ct i o n  a p p l i e s  t o  b o t h  n e w  p o o l  a n d  

se

a so

n a l  st a r t - u p .

1. 

Turn off the pump. Switch off the circuit breaker 
to the pump motor.

Summary of Contents for CV Versa-Plumb Series





















Reviews: