background image

Page 6 

ENGLISH

  

 

Jandy

®

 Pro Series, WaterColors RGBW LED Lights   

|

   Installation Manual

Figure 1.  Jandy Pro Series Digital Color Light 

Installation

3.2  Installing the Light Fixture 

NOTE 

Perform these steps 

only

 after the electrical system 

requirements are met.

1. 

Feed cord through conduit to junction box, 

leaving at least four (4) feet of cord at the light 

fixture to coil into the base of the light niche, see 

Figure 1. The four (4) feet of cord allows the light 

to be serviced after the pool is filled with water.

2. 

Cut the cord at the junction box, leaving at least 

six (6) inches of cord to make connections.

3. 

Strip six (6) inches of the outer cord jacket to 

expose the three insulated wires. 

Be careful not to 

damage the insulation on the three (3) inner wires.

4. 

Install strain relief over cord jacket and connect 

all three (3) wires to the corresponding circuit 

wires in the junction box. Install the junction box 

cover.

5. 

Coil the 4-foot length of cord around the fixture 

or into the base of the pool niche, and place the 

light assembly into the niche.

6. 

Engage the retainer tab on the bottom of the face 

ring, then pivot the top of the fixture inward and  

tighten the special pilot screw.

 WARNING

Use only the special pilot screw provided with this 

underwater light. This screw mounts and electrically 

grounds the housing securely to the mounting ring 

and wet niche. Failure to use the screw provided could 

create an electrical hazard, which could result in death 

or serious injury to pool or spa users, installers or 

others due to electrical shock.

7. 

Fill the pool until the underwater light is 

completely submerged in water before operating 

the light for more than 2 minutes. The light will 

heat up quickly when operated outside of water. 

Turn on main switch or circuit breaker, and the 

switch, which operates the underwater light, to 

check for proper operation. Refer to 

Section 6, 

Operating Instructions.

 WARNING

Never operate this underwater light for more than 

10 seconds unless it is totally submerged in water. 

Without total submersion, the light assembly will get 

extremely hot, which may result in serious burns or in 

breakage of the bulb or lens. This may result in serious 

injury to pool or spa users, installers, or bystanders or 

damage to property.

Section 4.  Replacing Jandy Pro 

Series Light Fixture in 

an Existing Pool or Spa

 WARNING

Risk of Electrical Shock or Electrocution. 

This underwater light must be installed by a licensed 

or certified electrician or a qualified pool serviceman 

in accordance with the National Electrical Code and 

all applicable local codes and ordinances. Improper 

installation will create an electrical hazard, which could 

result in death or serious injury to pool or spa users, 

installers or others due to electrical shock, and may 

also cause damage to property. 

 

Always disconnect the power to the color light at the 

circuit breaker before installing or servicing the light. 

Failure to do so could result in death or serious injury 

to serviceman, pool or spa users or others due to 

electrical shock.

4.1  Preparing the Light Fixture for 

Replacement

Verify that the pool meets the requirements of the current 

National Electrical Code

®

 (NEC) and all local codes 

and ordinances. A licensed or certified electrician must 

install the electrical system to meet or exceed those 

requirements before the underwater light is installed. 

Some of the requirements of the National Electrical 

Code, which the pool’s electrical system must meet, are 

as follows:

1. 

The lighting circuit must have a Ground Fault 

Circuit Interrupter (GFCI) for 120 volt models, 

and must have an appropriately rated circuit 

breaker.

2. 

The junction box (or, for 12 volt models, the low 

voltage transformer) must be located at least eight 

(8) inches above water level, at least four (4) 

Summary of Contents for CPLVRGBWS30

















































Reviews: