background image

5

General Information 

 

 

ATTENTION!  BECOME ALERT!  YOUR SAFETY IS INVOLVED! 

 

Safety is a primary concern in the design and manufacture of our products.  Unfortunately, our efforts to provide safe equipment can 

be erased by an operator’s single careless act.  In addition, hazard control and accident prevention are dependent upon the awareness, 

concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.  

Make certain that the operator(s), prior to operating is instructed in safe and proper use and reviews and understands the manual(s) 

pertaining to this machine.  Also make certain that the operator(s) reviews and understands the operator’s manual of the tow vehicle 

prior to hooking up or operating the SpeedTender.

Read this manual before you operate this machine.  If you do not understand any part of this manual, or need more information, contact 

the manufacturer or your authorized dealer.

Safety Rules Continued on Next Page

SAFETY RULES:

TO THE OWNER:

The purpose of this manual is to assist you in operating and maintaining your header transport in a safe manner. Read it carefully. It 

furnishes information and instructions that will help you achieve years of dependable performance and help maintain safe operating 

conditions. If this machine is used by an employee or is loaned or rented, make certain that the operator(s), prior to operating:

1. Is instructed in safe and proper use.

2. Reviews and understands the manual(s) pertaining to this machine.

Throughout this manual, the term IMPORTANT is used to indicate that failure to observe can cause damage to equipment. The terms 

CAUTION, WARNING and DANGER are used in conjunction with the Safety-Alert Symbol, (a triangle with an exclamation mark), to indicate 

the degree of hazard for items of personal safety. When you see this symbol, carefully read the message that follows and be alert to the

possibility of personal injury or death.

 DANGER

 WARNING

 CAUTION

This Safety-Alert symbol indicates a hazard and means

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, 

and includes hazards that are exposed when guards are removed.

Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates that failure to observe can cause damage to equipment.

Indicates helpful information.

IMPORTANT

NOTE

Summary of Contents for 4WS15




























Reviews: