JAI SP-25000C-CXP4A User Manual Download Page 62

Page: 62 / 72

Setting range

Default value

Description

Configure settings for Lens Communication Control.

0, 1

Enable RS-232C for lens control.

ー

115200bps

Set the baud rate during communication.

[Setting range]
0:9600bps, 1:19200bps, 2:38400bps, 3:57600bps, 4:115200bps

0:7bit 1:8bit

Set the data length during communication.

0:None 1:Odd
2:Even

Set the presence or absence of parity bit during communication.

0:1bit 1:2bit

Set the stop bit during communication.

Update LensCommunicationRecvData
Displays data received from the lens to be controlled.
Transfers commands to the lens to be controlled.

Item

LensCommunicationControl

LensCommunicationRecvDataUpdate
LensCommunicationRecvData
LensCommunicationSendData

LensCommunicationEnable

LensCommunicationBaudrate

LensCommunicationDataBit

LensCommunicationParity

LensCommunicationStopBit

—

SP-25000M-CXP4A/SP-25000C-CXP4A

Summary of Contents for SP-25000C-CXP4A









































































Search results

Summary of Contents for SP-25000C-CXP4A

Reviews:

Related manuals for SP-25000C-CXP4A

Brands by name

Popular brands

JAI SP-25000C-CXP4A, User Manual

Search results

Summary of Contents for SP-25000C-CXP4A

Reviews:

Related manuals for SP-25000C-CXP4A

Brands by name

Popular brands