![background image](http://html.mh-extra.com/html/jai/cb-030ge/cb-030ge_user-manual_631452064.webp)
CM-030GE/CM-030GE-RA / CB-030GE/CB-030GE-RA
- 62 -
13.2. Specification table
Specifications
CM-030GE/CM-030GE-RA
CB-030GE/CB-030GE-RA
Scanning system
Progressive scan
Frame rate full frame
90.5 frames/sec. Progressive (511 lines/frame)
Pixel clock
40 MHz
Line frequency
46.296 kHz ( 1H = 21.6 µs ), (864 pixel clock/line)
CCD sensor
1/3”. Monochrome ICX424AL
1/3” Bayer Color ICX424AQ
Sensing area
4.85 (h) x 3.66 (v) mm 1/3 inch diagonal
Cell size
7.4 (h) x 7.4 (v)
m
Active pixels
656 (h) x 494 (v)
Pixels in video output.
Full Scan
2/3 partial Scan
1/2 partial Scan
1/4 partial Scan
1/8 partial Scan
Vertical Binning
Region-of-interest (ROI)
656 (h) x 494 (v) 90.5 fps. H = 46.296 kHz
656(h) x 326 (v) 128 fps H= 46.296kHz
656 (h) x 246 (v) 159 fps. H = 46.296 kHz
656 (h) x 122 (v) 255 fps. H = 46.296kHz
656 (h) x 62 (v) 361 fps. H = 46.2965 kHz
656 (h) x 247 (v) 166.2 fps. H = 42.735 kHz ( *Note)
User Definable. Memory read-out
*Note: Vertical binning is for CM-030GE/CM-030GE-RA only
Sensitivity on sensor (minimum)
0.05 Lux (Max. gain, Shutter OFF, 50%
video )
0.4 Lux (Max. gain, Shutter OFF,50%
Green, w/IR cut filter)
S/N ratio
More than 50 dB (0dB gain)
Digital Video output.
GigE Vision Compliant
Mono8,Mono10,Mono10_Packed
GigE Vision Compliant
BAYRG8,BAYGB8,BAYRG10,BAYGB10
Iris video output. Analogue
0.7 V p-p , enabled by internal switch
Gain
Manual -3 to +24 dB (1 step=0.0358dB)
Synchronization
Internal X-tal
GPIO Module
Input/output switch
Clock Generator ( One)
Pulse Generators ( Four)
Configurable 14-in / 9-out switch
12-bit counter based on 25MHz clock or Pixel clock
20-bit counter programmable for length, start point, stop point, repeat
Hardware Trigger modes
Edge Pre-Select , Pulse Width Control, RCT,Frame Delay and Sequence
OB area transfer mode
ON / OFF
Event message
SYNC / ASYNC mode ( Trigger mode status when exposure starts )
Exposure start, Exposure end, Trigger IN, Video start, Video end
Electronic Shutter
Preset Shutter speed
Programmable exposure
Exposure Time (Abs)
GPIO plus Pulse Width
OFF(1/90) and 1/100 to 1/10,000 in 9 steps
2L(43.2µs) to 511L ( 11.037ms) in 1L steps
µsec – user definable. Same range as PE
max. 2 sec ( Can be set by 100µs unit or Pixel Clock unit)
Control interface
Register based. GigE Vision / GenIcam compliant
Functions controlled via GigE Vision
Interface
Shutter, Gain, Black Level, Trigger mode, Read out mode,
GPIO setup ,ROI ( GenIcam mandatory functions )
GigE Vision Streaming Control
Packet size, Delayed ( Frame ) read-out, inter-packet delay
Jumbo frame can be set at max. 4K(4040) , Default packet size is 1428 Byte.
Indicators on rear panel
Power, Hardware trigger, GigE Link, GigE activity
Operating temperature
-5
C to +45
C
Humidity
20 – 90% non-condensing
Storage temp/humidity
-25
C to +60
C/20% to 90% non-condensing
Vibration
10G (20Hz to 200Hz, XYZ)
Shock
70G
Regulatory
CE (EN61000-6-2 and EN61000-6-3), FCC part 15 class B, RoHS, WEEE