background image

Tool change

Item no. 10408020-01, Revision 03

31 ( 44 )

10.2

Pneumatic taper change

DANGER: Due to flying parts.

The taper cleaning could build up air pressure in the hollow shank taper dur-
ing the tool taper change. This air pressure flings out the hollow shank taper
in the case of sudden release.

u

Always switch off the taper cleaning when the hollow shank taper is ap-
prox. 1-2 mm away from the contact surface.

Tip: Ensure concentric run-out quality.

u

Keep collet, clamping nut, contact surface, shaft, tool taper, and tool
mount clean at all times.

u

Check the tool taper mount.

It must be free of damage and clean when switching to the HF spindle.

Insert the tool up to the contact

surface of the clamping taper.

Ü

Make sure that the shaft of the HF spindle has come to an absolute stand-
still.

Ü

Switch on the compressed air for “cylinder forward”.

Ü

Remove the tool.

Ü

Clean the inner taper of the tool mount and the inner taper of the shaft
with the felt cleaning taper.

Ü

Insert the tool.

Ä

Insert the tool up to the contact surface of the clamping taper.

Ü

Switch on the compressed air for “cylinder back”.

Ü

Wait for 1-2 seconds after the tool change.

Ü

Start the HF spindle.

10.2.1

Automatic hollow shank taper tool clamp

Coaxiality tolerance

We recommend the following values:

Ü

Coaxiality tolerance when changing the tool.

Ä

Coaxiality (ØG): 0,8 mm

Ü

Contact force on clamping taper.

Ä

Maximum: 220 N

Summary of Contents for F120-H830.10 S11W2V













































Reviews: